Zenoah Brush Cutter BC2310DL User Manual

848J9893A1 (708)  
G
B
OWNER’S MANUAL  
BRUSHCUTTERS  
BC2310DL  
 
BC2310DL  
G
B
EC DECLARATION OF COMFORMITY  
We,  
ZENOAH CO., LTD.  
1-9, Minamidai, Kawagoe, Saitama, Japan  
declare in sole responsibility that the following products referred to in this  
declaration conform with  
DIRECTIVE 89/336/EEC, 98/37/EC, 2000/14/EC, 2002/88/EC, 2002/44/EC  
EN ISO 11806 : 1997  
The products referred to are:  
DESIGNATION  
MODELS  
: BRUSHCUTTER  
: BC2310DL  
SERIAL NUMBERS  
: 51100101 and up  
The company named above will keep on file the following technical docu-  
mentation for any inspection purpose.  
• Operation instructions  
• Plans and Drawings  
• Description of measures designed to ensure conformity  
• Other technical documentation  
:Specification sheet  
Inspection standard  
Saitama, Japan  
1st April 2007  
Masahiko GOUDA  
General Manager, Quality Assurance Department  
SAFETY FIRST  
Instructions contained in warnings within this manual marked  
with a symbol concern critical points which must be taken  
Contents  
into consideration to prevent possible serious bodily injury, and  
for this reason you are requested to read all such instructions  
carefully and follow them without fail.  
1. Parts location .................................................. 4  
2. Specifications ................................................. 4  
3. Warning labels on the machine ...................... 5  
4. Symbols on the machine ................................ 5  
5. For safe operation........................................... 6  
6. Set up ............................................................. 9  
7. Fuel ............................................................... 10  
8. Operation ...................................................... 11  
9. Maintenance ................................................. 13  
10. Storage ......................................................... 15  
11. Disposal ........................................................ 15  
12. Troubleshooting guide .................................. 16  
WARNINGS IN THE MANUAL  
WARNING  
This mark indicates instructions, which must be followed in or-  
der to prevent accidents, which could lead to serious bodily in-  
jury or death.  
IMPORTANT  
This mark indicates instructions, which must be followed, or it  
leads to mechanical failure, breakdown, or damage.  
NOTE  
This mark indicates hints or directions useful in the use of the  
product.  
GB-3  
 
BC2310DL  
1. Parts location  
5
(1) Primer pump  
(2) Air cleaner cover  
(3) Choke lever  
3
14  
2
1
13  
(4) Fuel tank  
4
(5) Starter knob  
(6) Line head  
11  
12  
(7) Gear case  
9
(8) Cutting attachment guard  
(9) Loop handle  
(10) Shaft tube  
(11) Suspention point  
(12) Throttle trigger  
(13) Stop switch  
(14) Throttle cable  
10  
7
8
6
2. Specification  
Overall size (L 3 W 3 H) ........................................................... 1765 x 330 x 310 mm  
Dry weight .......................................................................................................... 5.4 kg  
Engine  
Type ............................................................................ Air-cooled 2-stroke gasoline  
Model ............................................................................................. Zenoah G24LS  
Displacement ........................................................................................... 22.5 cm3  
Fuel............................................................................ Mixture (Gasoline 50 : Oil 1)  
(when using ZENOAH genuine oil)  
Carburetor .................................................................................... Diaphragm type  
Ignition system ................................................................................................ C.D.I  
Spark plug ........................................................................................ NGK BPMR7A  
Fuel tank capacity................................................................................................. 0.6 L  
Starter ...................................................................................................... Recoil starter  
Clutch.................................................................................................. Centrifugal type  
Reduction ratio .................................................................................................... 1.462  
Cutting head rotating direction ............................. Counter-clockwise (Operator view)  
Specifications are subject to change without notice.  
GB-4  
 
BC2310DL  
3. Warning labels on the machine  
15m (50ft)  
G
B
(1)  
(2)  
(3)  
(4)  
(5)  
(6)  
(7)  
(1) Read owner’s manual before operating this machine.  
(2) Wear head, eye and ear protection.  
(3) Wear foot protection.  
(4) Wear gloves.  
(5) Beware of thrown objects.  
(6) Warning / Attention  
(7) Keep all children, bystanders and helpers 15 meters away from the machine.  
If warning label peels off or becomes soiled and  
impossible to read, you should contact the  
dealer from which you purchased the product  
to order new labels and affix them in the required  
location(s).  
Never modify your machine.  
We won’t warrant the machine, if you use the  
remodeled brushcutter or if you don’t observe  
the proper usage written in the manual.  
4. Symbols on the machine  
For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications,  
please be careful not to make a mistake.  
The port to refuel the “MIX GASOLINE”  
Position: FUEL TANK CAP  
The direction to close the choke  
Position: AIR CLEANER COVER  
The direction to open the choke  
Position: AIR CLEANER COVER  
GB-5  
 
BC2310DL  
5. For safe operation  
b. At night, at times of heavy fog,  
or at any other times when  
your field of vision might be  
limited and it would be diffi-  
cult to gain a clear view of the  
working area.  
1. Read this manual carefully until  
you completely understand and  
follow all safety and operating  
instructions.  
2. Keep this manual handy so that  
you may refer to it later when-  
ever any questions arise. Also  
note, if you have any questions  
which cannot be answered  
herein, contact the dealer from  
whom you purchased the prod-  
uct.  
c. During rain storms, during  
lightning storms, at times of  
strong or gale-force winds, or  
at any other times when  
weather conditions might  
make it unsafe to use the  
product.  
3. Always be sure to include this  
manual when selling, lending, or  
otherwise transferring the own-  
ership of this product.  
4. Never allow children or anyone  
unable to fully understand the  
directions given in the manual  
to use the machine.  
WORKING PLAN  
1. You should never use the prod-  
uct when under the influence of  
alcohol, when suffering from ex-  
haustion or lack of sleep, when  
suffering from drowsiness as a re-  
sult of having taken cold medicine  
or at any other time when a pos-  
sibility exists that your judgment  
might be impaired or that you  
might not be able to operate the  
product properly and in a safe  
manner.  
WORKING CONDITION  
1. When using the product, you  
should wear proper clothing and  
protective equipment.  
2. When planning your work sched-  
ule, allow plenty of time to rest.  
Limit the amount of time over  
which the product is to be used  
continuously to somewhere  
around 30 ~ 40 minutes per ses-  
sion, and take 10 ~ 20 minutes of  
rest between work sessions. Also  
try to keep the total amount of  
work performed in a single day  
under 2 hours or less.  
(1) Helmet  
(2) Ear protectors  
(3) Protection goggles or face  
protector  
(4) Thick work gloves  
(5) Non-slip-sole work boots  
2. And you should carry with you.  
(1) Attached tools  
(2) Properly reserved fuel  
(3) Spare blade  
(4) Things to notify your working  
area (rope, warning signs)  
(5) Whistle (for collaboration or  
emergency)  
(6) Hatchet or saw (for removal of  
obstacles)  
WARNING  
1. If you don’t observe the working  
time, or working manner (See  
“USING THE PRODUCT”), Re-  
petitive Stress Injury (RSI) could  
occur.  
3. Do not wear loose clothing, jew-  
elry, short trousers, sandals, or go  
barefoot. Do not wear anything  
which might be caught by a mov-  
ing part of the unit. Secure hair  
so it is above shoulder length.  
If you feel discomfort, redness and  
swelling of your fingers or any  
other part of your body, see a doc-  
tor before getting worse.  
2. To avoid noise complaints, in gen-  
eral, operate product between  
8 a.m. and 5 p.m. on weekdays  
and 9 a.m. to 5 p.m. on weekends.  
WORKING CIRCUMSTANCE  
1. Never start the engine inside a  
closed room or building. Exhaust  
gases contain dangerous carbon  
monoxide.  
2. Never use the product,  
a. when the ground is slippery  
or when you can’t maintain a  
steady posture.  
IMPORTANT  
Check and follow the local regu-  
lations as to sound level and  
hours of operations for the prod-  
uct.  
GB-6  
 
BC2310DL  
5. For safe operation  
and hold it firmly in place so as to  
ensure that neither the cutting  
part nor the throttle come into  
contact with any obstacle when  
the engine starts.  
BEFORE STARTING  
THE ENGINE  
1. The area within a perimeter of  
15 m of the person using the  
product should be considered a  
hazardous area into which no one  
should enter. If necessary, yellow  
warning rope, warning signs  
should be placed around the pe-  
rimeter of the area. When work is  
to be performed simultaneously  
by two or more persons, care  
should also be taken to constantly  
look around or otherwise check  
for the presence and locations of  
other people working so as to  
maintain a distance between  
each person sufficient to ensure  
safety.  
G
B
WARNING  
Never place the throttle into the  
high-speed position when starting  
the engine.  
3. After starting the engine, check  
to make sure that the cutting at-  
tachment stops rotating when the  
throttle is moved fully back to its  
original position. If it continues to  
rotate even after the throttle has  
been moved fully back, turn off  
the engine and take the unit to  
your authorized ZENOAH servic-  
ing dealer for repair.  
2. Check the condition of working  
area to avoid any accident by hit-  
ting hidden obstacles such as  
stumps, stones, cans, or broken  
glass.  
USING THE PRODUCT  
IMPORTANT  
IMPORTANT  
Cut only materials recommended by  
the manufacturer. And use only for  
tasks explained in the manual.  
Remove any obstacle before begin-  
ning work.  
1. Grip the handles firmly with both  
hands using your whole hand.  
Place your feet slightly apart  
(slightly further apart than the  
width of your shoulders) so that  
your weight is distributed evenly  
across both legs, and always be  
sure to maintain a steady, even  
posture while working.  
3. Inspect the entire unit for loose  
fasteners and fuel leakage. Make  
sure that the cutting attachment  
is properly installed and securely  
fastened.  
4. Be sure to attach the cutting at-  
tachment guard securely in  
place, or you may get serious in-  
jury.  
5. Always use the shoulder strap.  
Adjust the strap for comfort be-  
fore starting the engine. The strap  
should be adjusted so the left  
hand can comfortably hold the  
handlebar grip approximately  
waist high.  
2. Keep cutting attachment below  
waist level.  
3. Maintain the speed of the engine  
at the level required to perform  
cutting work, and never raise the  
speed of the engine above the  
level necessary.  
4. If the unit starts to shake or vi-  
brate, turn off the engine and  
check the whole unit. Do not use  
it until the trouble has been prop-  
erly corrected.  
5. Keep all parts of your body away  
from rotating cutting attachment  
and hot surfaces.  
6. Never touch the muffler, spark  
plug, or other metallic parts of the  
engine while the engine is in op-  
eration or immediately after shut-  
ting down the engine. Doing so  
STARTING THE ENGINE  
1. Keep bystanders and animals at  
least 15 m away from the operat-  
ing point. If you are approached,  
immediately stop the engine.  
2. The product is equipped with a  
centrifugal clutch mechanism, so  
the cutting attachment begins to  
rotate as soon as the engine is  
started by putting the throttle into  
the start position. When starting  
the engine, place the product  
onto the ground in a flat clear area  
GB-7  
 
BC2310DL  
5. For safe operation  
could result in serious burns or elec-  
trical shock.  
HANDLING FUEL  
1. The engine of the ZENOAH prod-  
uct is designed to run on a mixed  
fuel, which contains highly flam-  
mable gasoline. Never store cans  
of fuel or refill the tank of the unit  
in any place where there is a  
boiler, stove, wood fire, electrical  
sparks, welding sparks, or any  
other source of heat or fire which  
might ignite the fuel.  
IF SOMEONE COMES  
1. Guard against hazardous situa-  
tions at all times. Warn adults to  
keep pets and children away from  
the area. Be careful if you are ap-  
proached. Injury may result from  
flying debris.  
2. If someone calls out or otherwise  
interrupts you while working, al-  
ways be sure to turn off the en-  
gine before turning around.  
2. Never smoke while operating the  
unit or refilling its fuel tank.  
3. When refilling the tank, always  
turn off the engine and allow it to  
cool down. Take a careful look  
around to make sure that there are  
no sparks or open flames any-  
where nearby before refueling.  
4. Wipe spilled fuel completely us-  
ing a dry rag if any fuel spillage  
occurs during refueling.  
5. After refueling, screw the fuel cap  
back tightly onto the fuel tank and  
then carry the unit to a spot 3 m  
or more away from where it was  
refueled before turning on the en-  
gine.  
MAINTENANCE  
1. In order to maintain your product  
in proper working order, perform  
the maintenance and checking  
operations described in the  
manual at regular intervals.  
2. Always be sure to turn off the en-  
gine and disconnect the spark  
plug wire before performing any  
maintenance or checking proce-  
dures.  
WARNING  
The metallic parts reach high tem-  
peratures immediately after stop-  
ping the engine.  
TRANSPORTATION  
1. When hand-carrying the product,  
cover over the cutting part if nec-  
essary, lift up the product and  
carry it paying attention to the  
blade.  
2. Never transport the product over  
rough roads over long distances  
by vehicle without removing all  
fuel from the fuel tank. If doing so,  
fuel might leak from the tank dur-  
ing transport.  
3. When replacing the cutting at-  
tachment or any other part, or  
when replacing the oil or any lu-  
bricant, always be sure to use  
only ZENOAH products or  
products which have been cer-  
tified by ZENOAH for use with  
the ZENOAH product.  
4. In the event that any part must be  
replaced or any maintenance or  
repair work not described in this  
manual must be performed,  
please contact a representative  
from the store nearest ZENOAH  
authorized servicing dealer for  
assistance.  
5. Do not use any accessory or at-  
tachment other than those bear-  
ing the ZENOAH mark and rec-  
ommended for the unit.  
6. Under no circumstances should  
you ever take apart the product  
or alter it in any way. Doing so  
might result in the product be-  
coming damaged during opera-  
tion or the product becoming un-  
able to operate properly.  
GB-8  
 
BC2310DL  
6. Set up  
INSTALLING HANDLE  
• Mount the handle to the shaft tube and clamp it at a  
location that is comfortable to you.  
G
B
(1)  
(1) About 28cm (11 inches)  
INSTALLING CUTTING ATTACHMENT GUARD  
• Attach the cutting attachiment guard with the bolts  
provided while inserting the spacer between the guard  
and the pipe.  
• Attach the guard skirt on the guard.  
INSTALLING CUTTING HEAD  
1. Remove the plastic tube that is attached to the gear  
shaft.  
2. Firmly screw the line head assembly onto the gear  
shaft by hand while locking the gear shaft by insert-  
ing the tool into the upper holder on the gear box.  
GB-9  
 
BC2310DL  
7. Fuel  
FUEL  
3. Pour in all of the oil and agitate well.  
4. Pour in the rest of gasoline and agitate again for at  
least one minute. As some oils may be difficult to agi-  
tate depending on oil ingredients, sufficient agitation  
is necessary for the engine to last long. Be careful  
that, if the agitation is insufficient, there is an increased  
danger of early piston seizing due to abnormally lean  
mixture.  
WARNING  
Gasoline is very flammable. Avoid smoking or  
bringing any flame or sparks near fuel. Make sure  
to stop the engine and allow it cool before refuel-  
ing the unit. Select outdoor bare ground for fuel-  
ing and move at least 3 m (10 ft) away from the  
fueling point before starting the engine.  
5. Put a clear indication on the outside of the container  
to avoid mixing up with gasoline or other containers.  
6. Indicate the contents on outside of container for easy  
identification.  
FUELING THE UNIT  
1. Untwist and remove the fuel cap. Rest the cap on a  
dustless place.  
2. Put fuel into the fuel tank to 80% of the full capacity.  
3. Fasten the fuel cap securely and wipe up any fuel  
spillage around the unit.  
• The Zenoah engines are lubricated by oil specially  
formulated for air-cooled 2-cycle gasoline engine use.  
If Zenoah oil is not available, use an anti-oxidant  
added quality oil expressly labeled for air-cooled 2-  
cycle engine use (JASO FC GRADE OIL or ISO EGC  
GRADE).  
WARNING  
1. Select bare ground for fueling.  
2. Move at least 10 feet (3 meters) away from the fu-  
eling point before starting the engine.  
3. Stop the engine before refueling the unit. At that  
time, be sure to sufficiently agitate the mixed gaso-  
line in the container.  
• Do not use BIA or TCW (2-stroke water-cooling type)  
mixed oil.  
FOR YOUR ENGINE LIFE, AVOID:  
1. FUEL WITH NO OIL (RAW GASOLINE) – It will cause  
severe damage to the internal engine parts very  
quickly.  
2. GASOHOL – It can cause deterioration of rubber and/  
or plastic parts and disruption of engine lubrication.  
3. OIL FOR 4-CYCLE ENGINE USE – It can cause spark  
plug fouling, exhaust port blocking, or piston ring stick-  
ing.  
RECOMMENDED MIXING RATIO  
GASOLINE 50 : OIL 1  
<when using ZENOAH genuine oil>  
Exhaust emission are controlled by the funda-  
mental engine parameters and components (eq.,  
carburation, ignition timing and port timing) with-  
out addition of any major hardware or the intro-  
duction of an inert material during combustion.  
• These engines are certified to operate on unleaded  
gasoline.  
4. Mixed fuels which have been left unused for a pe-  
riod of one month or more may clog the carburetor  
and result in the engine failing to operate properly.  
5. In the case of storing the product for a long period of  
time, clean the fuel tank after rendering it empty. Next,  
activate the engine and empty the carburetor of the  
composite fuel.  
• Make sure to use gasoline with a minimum octane  
number of 89RON (USA/Canada: 87AL).  
• If you use a gasoline of a lower octane value than  
prescribed, there is a danger that the engine tem-  
perature may rise and an engine problem such as  
piston seizing may consequently occur.  
6. In the case of scrapping the used mixed oil container,  
scrap it only at an authorized repository site.  
NOTE  
• Unleaded gasoline is recommended to reduce the  
contamination of the air for the sake of your health  
and the environment.  
As for details of quality assurance, read the description  
in the section Limited Warranty carefully. Moreover, nor-  
mal wear and change in product with no functional influ-  
ence are not covered by the warranty. Also, be careful  
that, if the usage in the instruction manual is not observed  
as to the mixed gasoline, etc. described therein, it may  
not be covered by the warranty.  
• Poor quality gasolines or oils may damage sealing  
rings, fuel lines or fuel tank of the engine.  
HOW TO MIX FUEL  
IMPORTANT  
Pay attention to agitation.  
1. Measure out the quantities of gasoline and oil to be  
mixed.  
2. Put some of the gasoline into a clean, approved fuel  
container.  
GB-10  
 
BC2310DL  
8. Operation  
STARTING ENGINE  
WARNING  
WARNING  
The product is equipped with a centrifugal clutch  
mechanism, so the cutting attachment begins to ro-  
tate as soon as the engine is started by putting the  
throttle into the start position. When starting the en-  
gine, place the product onto the ground in a flat clear  
area and hold it firmly in place so as to ensure that  
neither the cutting part nor the throttle come into con-  
tact with any obstacle when the engine starts.  
The cutting head will start rotating upon the engine  
starts.  
G
B
1. Feed fuel into the fuel tank and tighten the cap se-  
curely.  
2. Rest the unit on a flat, firm place. Keep the cutting  
head off the ground and clear of surrounding objects,  
as it will start rotating upon starting of the engine.  
3. Push the primer pump several times until overflown  
fuel flows out in the clear tube.  
IMPORTANT  
Avoid pulling the rope to its end or returning it by re-  
leasing the knob. Such actions can cause starter fail-  
ures.  
7. Move the choke lever downward to open the choke.  
And restart engine.  
8. Allow the engine to warm up for a several minutes  
before starting operation.  
(1) Choke lever (2) Close (3) Open  
(4) Purimer pump  
NOTE  
4. Move the choke lever to the closed position.  
5. Set the ignition switch to the “I” position. Set the throttle  
lever to the start position (1 2 3).  
1. When restarting the engine immediately after stop-  
ping it, leave the choke open.  
Place the unit on a flat, firm place.  
Keep the cutting head clear of everything around it.  
2. Overchoking can make the engine hard to start due  
to excess fuel. When the engine failed to start after  
several attempts, open the choke and repeat pulling  
the rope, or remove the spark plug and dry it.  
Stop  
Start  
1
3. Ignition switch  
STOPPING ENGINE  
T
R
A
ST  
Stop  
Start  
Ignition switch  
2
T
R
A
T
S
6. While holding the unit firmly, pull out the starter rope  
quickly until engine fires.  
1. Release the throttle lever and run the engine for half  
a minute.  
2. Shift the ignition switch to the STOP position.  
IMPORTANT  
Except for an emergency, avoid stopping the engine  
while pulling the throttle lever.  
GB-11  
 
BC2310DL  
8. Operation  
ADJUSTING THROTTLE CABLE  
• The normal play is 1 or 2 mm when measured at the  
carburetor side end. Readjust with the cable adjuster  
as required.  
TRIMMING GRASS AND WEEDS  
• Always remember that the TIP of the line does cut-  
ting. You will achieve better results by not crowding  
the line into the cutting area. Allow the unit to trim at  
its own pace.  
1. Hold the unit so the head is off the ground and is tilted  
about 20 degrees toward the sweep direction.  
.04 in  
(1 ~ 2 mm)  
(1)  
(1) Cable adjuster  
ADJUSTING IDLING SPEED  
2. You can avoid thrown debris by sweeping from your  
left to the right.  
3. Use a slow, deliberate action to cut heavy growth.  
The rate of cutting motion will depend on the material  
being cut. Heavy growth will require slower action than  
will light growth.  
(1) Idle adjusting screw  
1. When the engine tends to stop frequently at idling  
mode, turn the adjusting screw clockwise.  
4. Never swing the unit so hard as you are in danger of  
losing your balance or control of the unit.  
2. When the cutting head keeps rotating after releasing  
the trigger, turn the adjusting screw counter-clockwise.  
5. Try to control the cutting motion with the hip rather  
than placing the full workload on the arm and hands.  
NOTE  
6. Take precautions to avoid wire, grass and dead, dry,  
long-stem weeds from wrapping around the head  
shaft. Such materials can stall the head and cause  
the clutch to slip, resulting in damage to the clutch  
system if repeated frequently.  
• Warm up the engine before adjusting the idling speed.  
CUTTING WORK (LINE HEAD USAGE)  
WARNING  
ADJUSTING THE LINE LENGTH  
• Your brush cutter is equipped with a semi- auto type  
nylon line head that allows the operator to advance  
the line without stopping the engine. When the line  
becomes short, lightly tap the head on the ground  
while running the engine at full throttle.  
1. Always wear eye protection such as safety  
goggles. Never lean over the rotating cutting head.  
Rocks or other debris could be thrown into eyes  
and face and cause serious personal injury.  
• Each time the head is bumped, the line advances  
about 25 mm. For better effect, tap the head on bear  
ground or hard soil. Avoid bumping in thick, tall grass  
as the engine may stall by overload.  
2. Keep the cutting attachment guard in place at all  
times when the unit is operated.  
GB-12  
 
BC2310DL  
9. Maintenance  
Every Every Every  
25 50 100  
hours hours hours  
after after after  
Before  
use  
System/components  
Procedure  
Note  
fuel leaks, fuel spillage  
fuel tank, air filter, fuel filter  
wipe out  
G
B
inspect/clean  
see adjusting  
idling speed  
clean and readjust  
plug gap  
replace, if necessary  
replace carburetor  
if necessary  
GAP: .025 in (0.6 ~ 0.7 mm)  
replace, if necessary  
idle adjusting screw  
spark plug  
cylinder fins, intake air cooling vent clean  
muffler, spark arrester, cylinder exhaust port clean  
throttle lever, ignition switch  
check operation  
replace if  
something’s wrong  
grease  
cutting parts  
gear case  
screws/nuts/bolts  
cutting attachment guard  
tighten/replace  
make sure to attach  
except adjusting screws  
FUEL FILTER  
• When the engine runs short of fuel supply, check the  
fuel cap and the fuel filter for blockage.  
WARNING  
Make sure that the engine has stopped and is cool  
before performing any service to the machine.  
Contact with moving cutting head or hot muffler  
may result in a personal injury.  
AIR FILTER  
• The air filter, if clogged, will reduce the engine perfor-  
mance. Check and clean the filter element in warm,  
soapy water as required. Dry completely before in-  
stalling. If the element is broken or shrunk, replace  
with a new one.  
(1) Fuel filter  
(1) Air filter  
GB-13  
 
BC2310DL  
9. Maintenance  
SPARK PLUG  
GEAR CASE  
• Starting failure and misfiring are often caused by a  
fouled spark plug. Clean the spark plug and check  
that the plug gap is in the correct range. For a re-  
placement plug, use the correct type specified by  
ZENOAH.  
• The reduction gears are lubricated by multipurpose,  
lithium-based grease in the gear case. Supply new  
grease every 25 hours of use or more often depend-  
ing on the job condition.  
• Remove the bolt opposit to the grease nipple before  
installing new grease to arrange for old grease to exit.  
0.6~0.7 mm  
REPLACEMENT PLUG IS A NGK BPMR7A.  
INTAKE AIR COOLING VENT  
WARNING  
IMPORTANT  
Note that using any spark plug other than those des-  
ignated may result in the engine failing to operate prop-  
erly or in the engine becoming overheated and dam-  
aged.  
To install the spark plug, first turn the plug until it is  
finger tight, then tighten it a quarter turn more with a  
socket wrench.  
Never touch the cylinder, muffler, or spark plugs  
with your bare hands immediately after stopping  
the engine. The engine can become very hot when  
in operation, and doing so could result in severe  
burns.  
When checking the machine to make sure that it  
is okay before using it, check the area around the  
muffler and remove any wood chips or leaves  
which have attached themselves to the  
brushcutter. Failing to do so could cause the muf-  
fler to become overheated and that in turn could  
cause the engine to catch on fire. Always make  
sure that the muffler is clean and free of wood  
chips, leaves, and other waste before use.  
150 ~ 220 kgf-cm  
TIGHTENING TORQUE:  
(14.7 ~ 21.6 N.m.)  
Check the intake air cooling vent and the area  
around the cylinder cooling fins after every 25  
hours of use for blockage, and remove any waste  
which has attached itself to the brushcutter. Note  
that it is necessary to remove the engine cover  
shown in (MA5) in order to be able to view the up-  
per part of the cylinder.  
MUFFLER  
WARNING  
IMPORTANT  
• Inspect periodically, the muffler for loose fasteners,  
any damage or corrosion. If any sign of exhaust leak-  
age is found, stop using the machine and have it re-  
paired immediately.  
Note that failing to do so may result in the engine  
catching on fire.  
If waste gets stuck and causes blockage around the  
intake air cooling vent or between the cylinder fins, it  
may cause the engine to overheat, and that in turn  
may cause mechanical failure on the part of the  
brushcutter.  
(1) Intake air cooling vent  
GB-14  
 
BC2310DL  
9. Maintenance  
PROCEDURES TO BE PERFORMED AFTER  
EVERY 100 HOURS OF USE  
4. Wind up the line in the correct direction as indicated  
on the spool.  
G
B
1. Remove the muffler, insert a screwdriver into the vent,  
and wipe away any carbon buildup. Wipe away any  
carbon buildup on the muffler exhaust vent and cylin-  
der exhaust port at the same time.  
5. Hook each end of the line in the slot on the edge of  
the spool, and then put the ends through the eyelets  
on the housing. Make sure that the spring and the  
washers are in place.  
2. Tighten all screws, bolts, and fittings.  
3. Check to see if any oil or grease has worked its way  
in between the clutch lining and drum, and if it has,  
wipe it away using oil-free, lead-free gasoline.  
REFILLING TRIMMING LINE  
1. For replacement line, use a diameter of  
2.4 mm. The spool is capable for a line upto  
6 m on the 4" head. Avoid using a larger line as it may  
cut down the trimming performance.  
6. While holding the spool against the housing, pull the  
line ends to release them from the slot.  
WARNING  
For safety reasons, do not use metal reinforced line.  
2. Pinch the slotted area on the both sides of the spool  
housing to unhook the bottom cap.  
7. Line up the slot on the bottom cap with the hook on  
the housing, press the cap against the housing until it  
clicks.  
3. Take out the spool and pull off the old line. Put one  
end of new line through the spool holes and pull it  
until the length is equal between each part of the line.  
10. Storage  
Aged fuel is one of major causes of engine starting fail-  
ure. Before storing the unit, empty the fuel tank and run  
the engine until it uses all the fuel left in the fuel line and  
the carburetor. Store the unit indoor taking necessary  
measures for rust prevention.  
11. Disposal  
When disposing your machine, fuel or oil for the machine,  
be sure to allow your local regulations.  
GB-15  
 
BC2310DL  
12. Troubleshooting guide  
Case 1. Starting failure  
CHECK  
fuel tank  
fuel filter  
PROBABLE CAUSES  
incorrect fuel  
fuel filter is clogged  
ACTION  
drain it and use correct fuel  
clean  
carburetor adjustment screw out of normal range  
adjust to normal range  
clean/dry  
correct (GAP: 0.6 ~ 0.7 mm)  
retighten  
sparking (no spark)  
spark plug  
spark plug is fouled/wet  
plug gap is incorrect  
disconnected  
Case 2. Engine starts but does not keep running/hard re-starting  
CHECK  
PROBABLE CAUSES  
ACTION  
fuel tank  
incorrect fuel or staled fuel drain it and use correct fuel  
carburetor adjustment screw out of normal range  
muffler, cylinder (exhaust port) carbon is built-up  
adjust to normal range  
wipe away  
wash  
air cleaner  
clogged with dust  
clogged with dust  
cylinder fin, fan cover  
clean  
When your unit seems to need further service, please consult with our ZENOAH service shop in your area.  
Limited warranty  
Should any failure occur on the product under normal oper-  
ating conditions within the applicable warranty period, the  
failed part will be replaced or repaired free of charge by a  
ZENOAH authorized dealer.  
WARRANTY MAINTENANCE OR REPAIRS, AND SHALL  
NOT REDUCE THE WARRANTY OBLIGATION OF THE  
COMPANY.  
THE COMPANY IS LIABLE FOR DAMAGES TO OTHER  
ENGINE COMPONENTS CAUSED BY THE FAIRURE OF A  
WARRANTED PARTS STILL UNDER WARRANTY.  
WARRANTY PERIOD: 1 year (6 months if used profession-  
ally, and 30 days if used for rental purpose) from the date of  
initial purchase.  
THE WARRANTY DOES NOT APPLY TO THOSE UNITS  
WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF IN-  
STRUCTION LISTED IN THE OWNER/OPERATOR MANUAL  
FOR PROPER USE AND MAINTENANCE OF THE UNITS  
ACCIDENT MISHANDLING, ALTERATION, ABUSE, IM-  
PROPER LUBRICATION, USE OF ANY PARTS OR ACCES-  
SARIES OTHER THAN THOSE SPECIFIED BY THE COM-  
PANY, OR OTHER CAUSES BEYOND THE COMPANY’S  
CONTROL.  
THE PURCHASER SHALL BEAR COSTS OF TRANS-  
PORTING THE UNIT TO AND FROM THE ZENOAH DEALER.  
THE PURCHASER SHALL NOT BE CHARGED FOR DIAG-  
NOSTIC LABOR WHICH LEADS TO THE DETERMINATION  
THAT A WARRANTED PART IS DEFECTIVE, IF THE DIAG-  
NOSTIC WORK IS PERFORMED AT THE ZENOAH DEALER.  
THE PURCHASER OR OWNER IS RESPONSIBLE FOR THE  
PERFORMANCE OF THE REQUIRED MAINTENANCE AS  
DEFINED BY THE MANUFACTURER IN THE OWNER/OP-  
ERATOR MANUAL.  
THIS WARRANTY DOES NOT COVER THOSE PARTS RE-  
PLACED BY NORMAL WEAR OR HARMLESS CHANGES  
IN THEIR APPEARANCE.  
ANY WARRANTED PART WHICH IS NOT SCHEDULED FOR  
REPLACEMENT AS REQUIRED MAINTENANCE, OR  
WHICH IS SCHEDULED ONLY FOR REGULAR INSPECTION  
TO THE EFFECT OF REPAIR OR “REPLACE AS NECES-  
SARY” SHALL BE WARRANTED FOR THE WARRANTY PE-  
RIOD. ANY WARRANTED PART WHICH IS SCHEDULED  
FOR REPLACEMENT AS REQUIRED MAINTENANCE  
SHALL BE WARRANTED FOR THE PERIOD OF TIME UP  
TO THE FIRST SCHEDULED REPLACEMENT POINT FOR  
THE PART.  
THERE ARE NO OTHER EXPRESS WARRANTIES.  
IMPLIED WARRANTIES INCLUDING THOSE OF MER-  
CHANTABILITY AND FITNESS FOR A PARTICULAR PUR-  
POSE ARE LIMITED TO TWO (2) YEARS OF HOME USE  
[ONE (1) YEAR FOR ANY OTHER USE] FROM THE ORIGI-  
NAL DELIVERY DATE.  
LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL  
DAMAGE UNDER ANY AND ALL WARRANTIES ARE  
EXCLUDED.  
ANY REPLACEMENT PART THAT IS EQUIVALENT IN PER-  
FORMANCE AND DULABILITY MAY BE USED IN NON-  
IF YOU NEED TO OBTAIN MORE INFORMATION, PLEASE  
C A L L Y O U R N E A R E S T S E R V I C E C E N T E R ,  
OR CHECK PLEASE ZENOAH WEB SITE  
GB-16  
 

Weed Eater Tiller WER500A User Manual
White Rodgers Marine Heating System 37 0883 User Manual
Windsor Vacuum Cleaner SRXP12 User Manual
Xircom Modem 100Base TX User Manual
Yamaha Portable Speaker F2112 ASW User Manual
Zanussi Cooktop ZCV560M User Manual
Zanussi Food Warmer Cook Plate User Manual
Zanussi Freezer ZEUT 6245 User Manual
Zanussi Fryer 285764 User Manual
Zanussi Refrigerator ZT 52 RL User Manual