Zanussi Washer 132973860 User Manual

User  
manual  
Washing  
Machine  
ZWF 10070 W  
ZWF 12070 W  
ZWF 12070 S  
ZWF 14070 W  
ZWF 16070 W  
ZWF 16070 S  
 
Safety information  
In the interest of your safety and to ensure  
the correct use, before installing and first  
using the appliance, read this user manual  
carefully, including its hints and warnings.  
To avoid unnecessary mistakes and  
accidents, it is important to ensure that all  
people using the appliance are thoroughly  
familiar with its operation and safety  
features. Save these instructions and make  
sure that they remain with the appliance if it  
is moved or sold, so that everyone using it  
through its life will be properly informed on  
appliance use and safety.  
Always unplug the appliance and turn off the  
water supply after use, clean and  
maintenance.  
Under no circumstances should you attempt  
to repair the machine yourself. Repairs  
carried out by inexperienced persons may  
cause injury or serious malfunctioning.  
Contact your local Service Centre. Always  
insist on genuine spare parts.  
Installation  
This appliance is heavy. Care should be  
taken when moving it.  
When unpacking the appliance, check that it  
is not damaged. If in doubt, do not use it and  
contact the Service Centre.  
All packing and transit bolts must be  
removed before use. Serious damage can  
occur to the product and to property if this is  
not adhered to. See relevant section in the  
user manual.  
After having installed the appliance, check  
that it is not standing on the inlet and drain  
hose and the worktop is not pressing the  
electrical supply cable.  
If the machine is situated on a carpeted floor,  
please adjust the feet in order to allow air to  
circulate freely  
General safety  
It is dangerous to alter the specifications or  
attempt to modify this product in any way.  
During high temperature wash programmes  
the door glass may get hot. Do not touch it!  
Make sure that small pets do not climb into  
the drum. To avoid this, please check into  
the drum before using.  
Any objects such as coins, safety pins, nails,  
screws, stones or any other hard, sharp  
material can cause extensive damage and  
must not be placed into the machine.  
Only use the advised quantities of fabric  
softener and detergent. Damage to the fabric  
can ensue if you over-fill. Refer to the  
manufacturer’s recommendations of  
quantities.  
Always be sure, that there is no water  
leakage from hoses and their connections  
after the installation.  
Wash small items such as socks, laces,  
washable belts etc in a washing bag or  
pillow case as it is possible for such items to  
slip down between the tub and the inner  
drum.  
Do not use your washing machine to wash  
articles with whalebones, material without  
hems or torn material.  
If the appliance is installed in a location  
subject to frost, please read the «dangers of  
freezing» chapter.  
Any plumbing work required to install this  
appliance should be carried out by a  
qualified plumber or competent person.  
Any electrical work required to install this  
appliance should be carried out by a  
qualified electrician or competent person.  
 
3
Make sure that children or pets do not climb  
into the drum. To avoid this the machine  
incorporates special feature.  
Use  
This appliance is designed for domestic use.  
It must not be used for purposes other than  
those for which it was designed.  
Only wash fabrics which are designed to be  
machine washed. Follow the instructions on  
each garment label.  
Do not overload the appliance. See the  
relevant section in the user manual.  
Before washing, ensure that all pockets are  
empty and buttons and zips are fastened.  
Avoid washing frayed or torn articles and  
treat stains such as paint, ink, rust, and  
grass before washing. Underwired bras must  
NOT be machine washed.  
Garments which have been in contact with  
volatile petroleum products should not be  
machine washed. If volatile cleaning fluids  
are used, care should be taken to ensure  
that the fluid is removed from the garment  
before placing in the machine.  
To activate this device, To disable this device  
rotate the button  
and restore the  
(without pressing it)  
inside the door  
possibility of closing the  
door, rotate the button  
anti-clockwise until the  
groove is vertical.  
clockwise until the  
groove is horizontal. If  
necessary use a coin.  
Never pull the power supply cable to remove  
the plug from the socket; always take hold of  
the plug itself.  
Never use the washing machine if the power  
supply cable, the control panel, the working  
surface or the base are damaged so that the  
inside of the washing machine is accessible.  
Child safety  
This washing machine is not intended for  
use by young children or infirm persons  
without supervision.  
Young children should be supervised to  
ensure that they do not play with the  
appliance.  
The packaging components (e.g. plastic film,  
polystyrene) can be dangerous to children -  
danger of suffocation! Keep them out of  
children’s reach  
Keep all detergents in a safe place out of  
children’s reach.  
 
4
Description of the appliance  
1
Detergent dispenser drawer  
1
2
2
Control panel  
3
Door opening handle  
Special  
Off  
Cottons  
Sport 40°  
95°  
3h  
6h  
9h  
Sport Shoes 40°  
60° Eco  
60°  
1000  
900  
Silk  
Wash  
Door  
End  
Mini 30'  
40° Eco  
700  
Prewash  
Intensive  
4
Cold  
40°  
Synthetics  
50°  
Hand  
Super  
Quick  
Wash  
30°  
1000 6kg  
Start/Pause  
Options  
Extra Rinse  
Drain pump  
Spin  
Wool  
Spin  
40°  
Easy Iron 40°  
Drain  
40°  
ZWF10070W  
R
i
n
s
e
3
0
°
Delicates  
5
Adjustable feet  
3
4
5
Detergent dispenser drawer  
Prewash  
Wash  
Fabric Softener  
 
5
Control panel and functions  
Delay Start  
Special  
Off  
Cottons  
Sport 40°  
95°  
3h  
6h  
9h  
Sport Shoes 40°  
60° Eco  
60°  
1000  
900  
Silk  
Wash  
Door  
End  
Mini 30'  
40° Eco  
Prewash  
Intensive  
700  
Cold  
40°  
Synthetics  
50°  
Super  
Quick  
Hand  
Wash  
30°  
Start/Pause  
Extra Rinse  
Options  
Spin  
Wool  
Spin  
40°  
Easy Iron 40°  
40°  
Drain  
ZWF10070W  
Rinse 30°  
Delicates  
7
1
2
3
4
5
6
The programme selector dial allows to select a  
Programme selector dial and  
On/Off switch  
programme and/or to switch the machine on/off. It can be  
turned either clockwise or anticlockwise. The light  
Start/Pause starts to flash.  
1
2
Press the Spin button repeatedly to change the spin  
speed, if you want your laundry to be spun at a speed  
different from the one proposed by the washing machine  
or to select the Night cycle and Rinse Hold. The relevant  
light will light up.  
Spin reduction button  
By means of the Options button, you can select only one  
of the following option: Prewash, Intensive, Super Quick  
(see the relevant chapter «Operating sequence»).  
The relevant light will light up.  
Options button  
3
4
By means of this button, the machine performs some  
additional rinses.  
Extra Rinse button  
The Start/Pause button allows to start the selected  
programme; the corresponding green pilot light stops  
flashing.  
Start/Pause button  
5
This button interrupts also a programme which is running,  
the corresponding green pilot light starts to flash.  
The different pilot lights illuminate depending on the  
running programme phase.  
Programme progress display  
Delay Start button  
6
7
This button makes it possible to delay the starting of the  
washing programme by 3, 6, and 9 hours.  
 
6
Programme table  
Programme/  
Temperature  
Description of  
programme  
Type of laundry  
Options  
White cotton (heavy  
Spin red.  
Main wash at 95°C  
3 rinses  
Long spin  
Cottons  
95°  
soiled cotton items): e.g.  
sheets, tablecloths,  
Prewash, Intensive,  
Super Quick  
household linen, towels.  
Extra rinse  
White and fast  
coloured cotton  
(normally soiled cotton  
Main wash at 60°C  
3 rinses  
Cottons  
Spin red.  
60° Eco  
items): sheets, household Prewash, Extra rinse Long spin  
linen, underwear,  
Main wash at  
60° - 40°C  
3 rinses  
Spin red.  
Coloured cotton lightly  
soiled, shirts, blouses,  
towels, underwear.  
Cottons  
60° - 40°  
Prewash, Intensive,  
S. Quick, Extra rinse  
Long spin  
Coloured cotton lightly  
soiled, shirts, blouses,  
underwear.  
Main wash at 40°  
3 rinses  
Long spin  
Cottons  
40° Eco  
Spin red.  
Prewash, Extra rinse  
Spin red.  
Synthetic or mixed  
fabrics, underwear,  
coloured garments, non-  
shrink shirts, blouses.  
Main wash at  
50° - 40°  
3 rinses  
Synthetics  
50° - 40°  
Prewash, Intensive,  
Super Quick  
Extra rinse  
Short spin  
Synthetic or mixed  
fabrics to be gentle  
washed and spun.  
Main wash at 40°  
4 rinses  
Short spin  
Synthetics  
Easy iron 40°  
Spin red.  
Prewash, Extra rinse  
Main wash at  
40°-30°C  
3 rinses  
Delicates  
40° - 30°  
Delicate fabrics, for  
example curtains.  
Prewash, Intensive,  
Super Quick,  
Short spin  
Extra Rinse  
Max load for Cottons..................................6 kg  
Max load for Synthetics..............................3 kg  
Max load for Delicates ..............................3 kg  
 
7
Programme table  
Programme/  
Temperature  
Description of  
programme  
Type of laundry  
Options  
Programme for wool  
«Pure new wool, non-  
shrink, machine  
Main wash at 40°  
3 rinses  
Short spin  
Wool  
40°  
Spin red.,  
,
,
washable» label.  
Main wash at  
30° - Cold  
3 rinses  
Handwash  
30° - Cold  
Special programme for  
hand washing fabrics  
Spin red.,  
Short spin  
Main Wash at 30°C  
2 rinses  
Short spin  
Mini 30’  
30°  
Short cycle for lightly  
soiled fabrics  
Main wash at 30°C  
2 rinses  
Short spin  
Silk  
30°  
Silk items to be gentle  
washed and spun.  
,
Short cycle for 1 pair of  
sport shoes  
(2 pairs if they are small)  
Main Wash at 40°C  
3 rinses  
Short spin  
Sport  
Spin Red.,  
Shoes 40°  
Prewash, Extra rinse  
Prewash at 30°C  
Main wash at 40°C  
3 rinses  
Programme for heavily  
soiled synthetics items  
Spin Red.,  
,
Sport 40°  
Rinse  
Extra rinse  
Short spin  
Separate rinse cycle for  
hand washed items of  
cotton fabric.  
3 rinses  
Long spin  
Spin red.  
Extra rinse  
For emptying out the last  
rinse water in  
programmes with the  
Rinse Hold or Night  
Cycle option.  
Drain  
Spin  
Draining of water  
Drain and long spin  
Separate spin for  
cottons.  
Spin red.  
Max load for Wool/Handwash .............................. 2 kg  
Max load for Mini 30.......................................... 2.5 kg  
Max load for Silk ....................................................1 kg  
Max load for Sport Shoes 40° ............................1 pair  
(2 pairs if they are small)  
Max load for Sport 40° ..........................................3 kg  
 
8
Programme information  
Washing programme for machine washable wool as well as for hand  
washable woollens and delicate fabrics with the «hand washing»  
care symbol  
Wool and  
Handwash  
.
Selecting this programme the laundry is gently washed and spun to  
avoid any creasing. In this way ironing is easier. Furthermore the  
machine will perform additional rinses.  
Easy Iron  
Rinse  
With this programme it is possible to rinse and spin cotton garments  
which have been washed by hand.  
The machine performs 3 rinses, followed by a final spin at maximum  
speed.  
The spin speed can be reduced by depressing Spin button.  
For emptying out the water of the last rinse in programmes with the  
Rinse Hold  
or Night Cycle  
option.  
Drain  
Spin  
Turn first the programme selector dial to «Off», then select  
programme Drain and depress the Start/Pause button.  
Separate spin for hand washed garments and after programmes  
with Rinse Hold  
programme the selector dial must be turned to «Off». You can  
choose the speed by means of the relevant button to adapt it to the  
fabrics to be spun.  
or Night Cycle  
option. Before selecting this  
With this programme it is possible to wash one pair of sport shoes  
(or 2 pairs if they are small). The shoes would be gently washed and  
spun. Washing temperature 40°C.  
Sport shoes 40°  
Note! Don't wash your sport shoes together with laundry.  
This programme is suitable for washing heavily soiled sport items of  
synthetic fabrics. The machine will add automatically a prewash  
phase before the main wash to eliminate mud stains.  
Sport 40°  
Note ! We recommend you not to put the detergent into the  
compartment  
of the detergent drawer.  
The spin speed is reduced to 900 rpm.  
To reset a programme and to switch off the machine turn the  
selector dial to Off. Now can a new programme be selected.  
Off = Cancelling  
 
9
Washing hints  
Sorting the laundry  
Maximum loads  
Follow the wash code symbols on each  
garment label and the manufacturer’s washing  
Recommended loads are indicated in the  
programme charts.  
instructions. Sort the laundry as follows: whites, General rules:  
coloureds, synthetics, delicates, woollens.  
Cotton, linen: drum full but not too tightly  
packed;  
Synthetics: drum no more than half full;  
Delicate fabrics and woollens: drum no more  
than one third full.  
Washing a maximum load makes the most  
efficient use of water and energy.  
For heavily soiled laundry, reduce the load  
size.  
Temperatures  
for normally soiled white cottons  
90° or 95°  
50°/60°  
and linen (e.g. tea cloths, towels,  
tablecloths, sheets...)  
for normally soiled, colour fast  
garments (e.g. shirts, night  
dresses, pyjamas....) in linen,  
cotton or synthetic fibres and for  
lightly soiled white cotton (e.g.  
underwear).  
Laundry weights  
The following weights are indicative:  
bathrobe  
napkin  
quilt cover  
sheet  
pillow case  
tablecloth  
1200 g  
100 g  
700 g  
500 g  
200 g  
250 g  
200 g  
100 g  
200 g  
100 g  
600 g  
200 g  
500 g  
100 g  
100 g  
for delicate items (e.g. net  
curtains), mixed laundry including  
30°-40°-Cold synthetic fibres and woollens  
bearing the label «pure new wool,  
machine washable, non-shrink».  
Before loading the laundry  
Never wash whites and coloureds together.  
Whites may lose their «whiteness» in the  
wash.  
New coloured items may run in the first wash;  
they should therefore be washed separately  
the first time.  
Make sure that no metal objects are left in  
the laundry (e.g. hair clips, safety pins,  
pins). Button up pillowcases, close zip  
fasteners, hooks and poppers. Tie any belts  
or long tapes.  
Remove persistent stains before washing.  
Rub particularly soiled areas with a special  
detergent or detergent paste.  
Treat curtains with special care. Remove hooks  
or tie them up in a bag or net.  
towelling towel  
tea cloth  
night dress  
ladies’ briefs  
man’s work shirt  
man’s shirt  
man’s pyjamas  
blouse  
men’s underpants  
Removing stains  
Stubborn stains may not be removed by just  
water and detergent. It is therefore advisable to  
treat them prior to washing.  
Blood: treat fresh stains with cold water. For  
dried stains, soak overnight in water with a  
special detergent then rub in the soap and  
water.  
 
10  
Oil based paint: moisten with benzine stain  
remover, lay the garment on a soft cloth and  
dab the stain; treat several times.  
etc.), the colour, washing temperature and  
degree of soiling.  
All commonly available washing machine  
detergents may be used in this appliance:  
Dried grease stains: moisten with turpentine,  
lay the garment on a soft surface and dab the  
stain with the fingertips and a cotton cloth.  
Rust: oxalic acid dissolved in hot water or a  
rust removing product used cold. Be careful  
with rust stains which are not recent since the  
cellulose structure will already have been  
damaged and the fabric tends to hole.  
Mould stains: treat with bleach, rinse well  
(whites and fast coloureds only).  
Grass: soap lightly and treat with bleach  
(whites and fast coloureds only).  
Ball point pen and glue: moisten with  
acetone (*), lay the garment on a soft cloth and  
dab the stain.  
Lipstick: moisten with acetone as above, then  
treat stains with methylated spirits. Remove  
any residual marks from white fabrics with  
bleach.  
Red wine: soak in water and detergent, rinse  
and treat with acetic or citric acid, then rinse.  
Treat any residual marks with bleach.  
Ink: depending on the type of ink, moisten the  
fabric first with acetone (*), then with acetic  
acid; treat any residual marks on white fabrics  
with bleach and then rinse thoroughly.  
Tar stains: first treat with stain remover,  
methylated spirits or benzine, then rub with  
detergent paste.  
powder detergents for all types of fabric,  
powder detergents for delicate fabrics (60°C  
max) and woollens,  
liquid detergents, preferably for low  
temperature wash programmes (60°C max)  
for all types of fabric, or special for woollens  
only.  
The detergent and any additives must be  
placed in the appropriate compartments of the  
dispenser drawer before starting the wash  
programme.  
If using concentrated powder or liquid  
detergents, a programme without prewash  
must be selected.  
The washing machine incorporates a  
recirculation system which allows an optimal  
use of the concentrated detergent.  
Pour liquid detergent into the dispenser drawer  
compartment marked  
the programme.  
just before starting  
Any fabric softener or starching additives must  
be poured into the compartment marked  
before starting the wash programme.  
Follow the product manufacturer’s  
recommendations on quantities to use and do  
not exceed the «MAX» mark in the  
detergent dispenser drawer.  
(*) do not use acetone on artificial silk.  
Detergents and additives  
Good washing results also depend on the  
choice of detergent and use of the correct  
quantities to avoid waste and protect the  
environment. Although biodegradable,  
detergents contain substances which, in large  
quantities, can upset the delicate balance of  
nature.  
The choice of detergent will depend on the  
type of fabric (delicates, woollens, cottons,  
 
11  
Quantity of detergent to be used  
Degrees of water hardness  
The type and quantity of detergent will depend  
on the type of fabric, load size, degree of  
soiling and hardness of the water used.  
Water hardness is classified in so-called  
«degrees» of hardness. Information on  
hardness of the water in your area can be  
obtained from the relevant water supply  
company, or from your local authority.  
Follow the product manufacturers’ instructions  
on quantities to use.  
Degrees  
Level Characteristic  
German  
°dH  
French  
°T.H.  
1
2
3
4
soft  
medium  
hard  
0-7  
8-14  
15-21  
> 21  
0-15  
16-25  
26-37  
> 37  
very hard  
Use less detergent if:  
you are washing a small load,  
the laundry is lightly soiled,  
large amounts of foam form during washing.  
Before the first use  
WARNING!  
Ensure that the electrical and water  
connections comply with the installation  
instructions.  
IMPORTANT!  
Remove the polystyrene block and any  
material from the drum.  
IMPORTANT!  
Pour 2 litres of water into the main wash  
compartment  
of the detergent drawer in  
order to activate the ECO valve. Then run a  
cotton cycle at 95°C, without any laundry in the  
machine, to remove any manufacturing residue  
from the drum and tub. Pour 1/2 a measure of  
detergent into the dispenser drawer and start  
the machine.  
 
12  
Operating sequence  
Position «Off» to Reset programme/Switching  
OFF of the machine.  
At the end of the programme the selector  
dial must be turned to position «Off», to  
switch the machine off.  
1. Load the laundry  
Open the door by  
carefully pulling the  
door handle outwards.  
Place the laundry in the  
drum, one item at a  
time, shaking them out  
IMPORTANT!  
If you turn the programme selector dial to  
another programme when the machine is  
working, the red Start/Pause pilot light will  
flash 3 times to indicate a wrong selection. The  
machine will not perform the new selected  
programme.  
as much as possible. Close the door.  
2. Measure out the detergent and the fabric  
softener  
4. Select the spin speed or Night Cycle or  
Rinse Hold option  
ZWF 10070 W  
ZWF 16070 W  
1000  
1600  
900  
900  
700  
700  
Pull out the dispenser drawer until it stops.  
Measure out the amount of detergent required,  
pour it into the main wash compartment  
and, if you wish to carry out a programme with  
the prewash phase, pour it into the  
Spin  
Spin  
compartment marked  
If required, pour fabric softener into the  
compartment marked  
not exceed the «MAX» mark in the drawer).  
Close the drawer gently.  
.
Press the Spin button repeatedly to change the  
spin speed, if you want your laundry to be spun  
at a speed different from the one proposed by  
the appliance.  
(the amount used must  
The relevant light will light up.  
Maximum speeds are:  
3. Select the required programme  
Cottons: 1000, 1200, 1400, 1600 rpm  
depending on the Model;  
Synthetics, Wool, Handwash, Sport Shoes  
40° and Sport 40°: 900 rpm  
The selector dial is  
divided into following  
sections:  
Special  
Off  
Cottons  
Sport 40°  
95°  
Sport Shoes 40°  
60° Eco  
60°  
Silk  
Mini 30'  
40° Eco  
Cold  
40°  
Synthetics  
50°  
Hand  
Wash  
Cottons,  
30°  
Delicates, Mini 30’ and Silk: 700 rpm;  
Wool  
Spin  
40°  
Easy Iron 40°  
Synthetics,  
Delicates,  
Special  
Drain  
40°  
Night Cycle  
: by selecting this option, the  
Rinse 30°  
Delicates  
machine will not drain the water of the last rinse,  
so as not to crease the laundry. As all spinning  
phases are suppressed, this washing cycle is  
very noiseless and it can be selectionned at  
night or in times with a more economical power  
The green Start/Pause light starts to flash.  
The selector dial can be turned either  
clockwise or anticlockwise.  
 
13  
Operating sequence  
Intensive: this option can be selected for heavily  
soiled laundry: the washing intensity will be  
increased and the washing time will be  
prolonged by few minutes depending on the  
selected type of fabric.  
This option can be selected with all cottons,  
Synthetics and Delicates programmes, except  
for Eco and Easy Iron programmes.  
rate. On Cotton, Synthetic, Delicates, Silk, Sport  
Shoes 40°, and Sport 40° programmes the  
rinses will be performed with more water. When  
the programme has finished the «Door» and  
«End» pilot lights are alight, the Start/Pause and  
«Wash» lights are off and the door is blocked to  
indicate that the water must be emptied out.  
Rinse Hold  
: by selecting this option the  
Super Quick: a very short cycle for slightly  
soiled items that have been used or worn for a  
short time.  
This option is not available with the Wool,  
Handwash, Mini 30’, Silk, Sport Shoes 40°, Easy  
Iron, Sport 40° and Eco programmes.  
water of the last rinse is not emptied out to  
prevent the fabrics from creasing. When the  
programme has finished the pilot lights «Door»  
and «End» are alight, the Start/Pause and  
«Wash» lights are off and the door is locked to  
indicate that the water must be emptied out.  
The max. load recommended for cotton: is 3 kg  
and for synthetic and delicate is 1.5 kg.  
To empty out the water:  
1.turn the programme selector dial to «Off»  
2.select the Drain or Spin programme  
3.reduce the spin speed if needed, by means of  
the relevant button  
4.depress Start/Pause button  
5. at the end of programme, only the pilot lights  
End comes on.  
IMPORTANT!  
If an option is chosen that is not allowed with the  
selected programme, the red pilot light of the  
Start/Pause button will flash 3 times.  
The washing time will be reduced according to  
the type of fabric and the selected temperature.  
5. Select Prewash, Intensive, Super Quick  
option  
6. Select the Extra Rinse option  
Prewash  
Press the «Options»  
button repeatedly, to  
select only one of the  
This button can be  
selected with all  
programmes except the  
Intensive  
Super  
Quick  
Extra Rinse  
Options  
available options. The  
relevant light will light  
up.  
Mini 30’, Silk, Wool and  
Hand wash  
programmes. The  
machine performs some  
additional rinses.  
Prewash: select this option if you wish your  
laundry to be prewashed at 30°C before the  
main wash (not available for Wool, Handwash,  
Mini 30’ and Silk). The prewash ends with a short  
spin in programmes for cotton and synthetic  
fabrics, and Sport 40°, whereas in the  
This option is recommended for people who are  
allergic to detergents, and in areas where the  
water is very soft.  
7. Select the Start/Pause  
To start the selected programme, press the  
Start/Pause button; the corresponding green pilot  
light stops flashing.  
programmes for delicate fabrics and Sport 40°  
Shoes the water is only drained.  
 
14  
Operating sequence  
• set the washing machine to PAUSE by  
pressing the Start/Pause button;  
• press the Delay Start button once, the light  
relevant to the selected delay goes off.  
• press the Start/Pause button again to start  
the programme.  
Wash  
The «Wash» and  
Door  
End  
«Door» lights are alight  
to indicate that the  
appliance starts  
operating and the door  
is locked.  
Start/Pause  
IMPORTANT!  
• The selected delay can be changed only  
after selecting the washing programme  
again.  
To interrupt a programme which is running,  
depress the Start/Pause button: the  
corresponding green pilot light starts to flash.  
To restart the programme from the point at  
which it was interrupted, press the Start/Pause  
button again.  
• The door will be locked throughout the delay  
time. If you need to open the door, you must  
first set the washing machine to PAUSE by  
pressing the Start/Pause button and then  
wait about 2 minutes untill the «Door» light  
has gone off. After you have closed the door,  
press the Start/Pause button again.  
The Delay Start can not be selected with Drain  
programmes.  
If you have chosen a delayed start, the machine  
will begin the countdown.  
IMPORTANT!  
If an incorrect option is selected, the red pilot  
light of the Start/ Pause button flashes for 3  
times.  
Programme progress display  
8. Select the Delay Start  
After having depress Start/Pause button, the  
«Wash» pilot light illuminates and stays on  
while the machine is working.  
Before you start the  
programme, if you wish  
Delay Start  
to delay the start, press  
3h  
6h  
9h  
the Delay Start button  
repeatedly, to select the  
desired delay.  
Wash  
Door  
End  
The relevant light illuminates.  
This button makes it possible to delay the  
starting of the washing programme by 3, 6, and  
9 hours.  
You must select this option after you have set  
the programme and before you press the  
Start/Pause button.  
The «Door» pilot light indicates if the door can  
be opened:  
• light on: the door cannot be opened.  
The appliance is running.  
• light off: the door can be opened.  
The washing programme is finished.  
• flashing light: the door is opening.  
When the programme has finished, the «End»  
pilot light illuminates and the «Wash» light  
goes off.  
You can cancel the delay time at any moment,  
before you press the Start/Pause button.  
If you have already pressed the Start/Pause  
button, and you wish to cancel the delay time,  
proceed as follows:  
 
15  
Altering an option or a running programme  
After about 2 minutes the door can be opened  
(pay attention to the water level and  
temperature!).  
It is possible to change any option before the  
programme carries it out. Before you make any  
change, you must pause the washing machine  
by pressing the Start/Pause button.  
Changing a running programme is possible  
only by resetting it. Turn the programme  
selector dial to Off and then to the new  
programme position. The washing water in the  
tub will not emptied out. Start the new  
programme by depressing the Start/Pause  
button again.  
At the end of the programme  
The machine stops automatically. The  
Start/Pause and «wash» lights go off and the  
«end» phase light illuminates. The door can be  
opened (the Door light is off).  
If the «Rinse Hold» or «Night Cycle» option  
has been selected, the «end» and «door»  
lights illuminates but the door remains locked  
to indicate that the water must be emptied out  
before opening the door.  
Interrupting a programme  
To empty out the water please read the steps  
on the Rinse Hold option paragraph.  
Turn the programme selector dial to «Off» to  
switch the machine off. Remove the laundry  
from the drum and carefully check that the  
drum is empty.  
If you do not intend to carry out another wash,  
close the water tap. Leave the door open to  
prevent the formation of mildew and  
unpleasant smells.  
Depress the Start/Pause button to interrupt a  
programme which is running, the  
corresponding light starts to flash. Depress the  
button again to restart the programme.  
Cancelling a programme  
Turn the selector dial to Off to cancel a  
programme which is running. Now you can  
select a new programme.  
Opening the door after the programme has  
started  
First set the machine to pause by pressing the  
Start/Pause button.  
If the «Door» light flashes and after 2 minutes  
goes off, the door can be opened.  
If the «Door» light does not flash, this means  
that the machine is already heating, that the  
water level is above the bottom edge of the  
door or that the drum is turning.  
In this case the door can not be opened.  
If you cannot open the door but you need to  
open it you have to switch the machine off by  
turning the selector dial to «Off».  
 
16  
Care and cleaning  
IMPORTANT!  
Remove the drawer by pressing the catch  
downwards and by pulling it out. Flush it out  
under a tap, to remove any traces of  
accumulated powder.  
You must DISCONNECT the appliance from  
the electricity supply, before you can carry out  
any cleaning or maintenance work.  
Cleaning the drawer recess  
Descaling  
The water we use normally contains lime. It is  
a good idea to periodically use a water  
softening powder in the machine. Do this  
separately from any laundry washing, and  
according to the softening powder  
manufacturer's instructions. This will help to  
prevent the formation of lime deposits.  
Having removed the  
drawer, use a small  
brush to clean the  
recess, ensuring that all  
washing powder  
residue is removed from  
the upper and lower  
Maintenance Wash  
part of the recess.  
With the use of low temperature washes it is  
possible to get a build up of residues inside the  
drum.  
We recommend that a maintenance wash be  
performed on a regular basis.  
Replace the drawer and run the rinse  
programme without any clothes in the drum.  
Cleaning the pump  
The pump should be inspected if  
To run a maintenance wash:  
the machine does not empty and/or spin  
the machine makes an unusual noise during  
draining due to objects such as safety pins,  
coins etc. blocking the pump.  
The drum should be empty of laundry.  
Select the hottest cotton wash programme.  
Use a normal measure of detergent, must be  
a powder with biological properties.  
Proceed as follows:  
Disconnect the appliance.  
If necessary wait until the water has cooled  
down.  
External cleaning  
Clean the exterior cabinet of the appliance with  
soap and water only, and then dry thoroughly.  
Open the pump door.  
Cleaning the dispenser drawer  
The washing powder and additive dispenser  
drawer should be cleaned regularly.  
Place a containfer  
close to the pump to  
collect any spillage.  
Pull out the emergency  
emptying hose, place it  
in the container and  
remove its cap.  
When no more water comes out, unscrew the  
pump cover and remove it. Always keep a  
rag nearby to dry up spillage of water when  
removing the cover.  
To aid cleaning, the top part of the additive  
compartment should be removed.  
 
17  
The dangers of freezing  
If the machine is exposed to temperatures  
below 0°C, certain precautions should be  
taken.  
Turn off the water tap.  
Unscrew the inlet hose.  
Place the end of the emergency emptying  
hose and that of the inlet hose in a bowl  
placed on the floor and let water drain out.  
Screw the water inlet hose back on and  
reposition the emergency emptying hose  
after having put the cap on again.  
When you intend to start the machine up  
again, make sure that the room temperature  
is above 0°C.  
Remove any objects from the pump impeller  
by rotating it.  
Put the cap back on the emergency emptying  
hose and place the latter back in its seat.  
Screw the pump cover  
fully in.  
Close the pump door.  
IMPORTANT!  
Every time you drain the water through the  
emergency emptying hose you must pour 2  
litres of water into the main wash compartment  
of the detergent drawer and then run the drain  
programme. This will activate the ECO VALVE  
device avoiding that part of the detergent  
remains unused at next washing.  
IMPORTANT!  
When the appliance is in use and depending  
on the programme selected there can be hot  
water in the pump.  
Emergency emptying out  
Never remove the pump cover during a wash  
cycle, always wait until the appliance has  
finished the cycle, and is empty. When  
replacing the cover, ensure it is securely  
retightened so as to stop leaks and young  
children being able to remove it.  
Cleaning the water inlet filter  
If your water is very hard or contains traces of  
lime deposit, the water inlet filter may become  
clogged.  
If the water is not discharged, proceed as  
follows to empty out the machine:  
pull out the plug from the power socket;  
close the water tap;  
if necessary, wait until the water has cooled  
down;  
open the pump door;  
place a bowl on the floor and place the end  
of the emergency emptying hose into the  
bowl. Remove its cap. The water should  
drain by gravity into the bowl. When the bowl  
is full, put the cap back on the hose. Empty  
the bowl. Repeat the procedure until water  
stops flowing out;  
It is therefore a good idea to clean it from time  
to time.  
Turn off the water tap.  
Unscrew the water inlet  
hose. Clean the filter  
using a hard bristle  
brush. Tighten up the  
inlet hose.  
clean the pump if necessary as previously  
described;  
replace the emergency emptying hose in its  
seat after having plugged it;  
screw the pump cover again and close the  
door.  
 
18  
Something not working  
IMPORTANT!  
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily  
without calling out an engineer. Before contacting your local Service Centre, please carry out the  
checks listed below.  
During machine operation it is possible that the red Start/Pause pilot light flashes to indicate that  
the machine is not working.  
Once the problem has been eliminated, press the Start/Pause button to restart the programme. If  
after all checks, the problem persists, contact your local Service Centre.  
Malfunction  
Possible Cause / Solution  
The door has not been closed. (Red Start/Pause  
pilot light flashes)  
• Close firmly the door.  
The plug is not properly inserted in the power socket.  
• Insert the plug into the power socket.  
There is no power at the socket.  
• Please check your domestic electrical installation.  
The main fuse has blown.  
• Replace the fuse.  
The washing machine does not start:  
The selector dial is not correctly positioned and the  
Start/Pause button has not been depressed.  
• Please turn the selector dial and press the  
Start/Pause button again.  
The delay start has been selected.  
• If the laundry are to be washed immediately, cancel  
the delay start  
The water tap is closed. (Red Start/Pause pilot light  
flashes)  
• Open the water tap.  
The inlet hose is squashed or kinked.  
(Red Start/Pause pilot light flashes)  
• Check the inlet hose connection.  
The machine does not fill:  
The filter in the inlet hose is blocked.  
(Red Start/Pause pilot light flashes)  
• Clean the water inlet hose filter.  
The door is not properly closed.  
(Red Start/Pause pilot light flashes)  
• Close firmly the door.  
 
19  
Malfunction  
Possible Cause / Solution  
The end of the drain hose is too low.  
• Refer to relevant paragraph in «water drainage»  
section.  
The machine fills then empties  
immediately:  
The drain hose is squashed or kinked.  
(Red Start/ Pause pilot light flashes)  
• Check the drain hose connection.  
The drain pump is clogged.  
(Red Start/Pause pilot light flashes)  
• Clean the drain pump.  
The machine does not empty and/or  
does not spin:  
The option  
or  
has been selected.  
• Select the Drain or Spin programmes  
The laundry is not evenly distributed in the drum.  
• Redistribute the laundry.  
Too much detergent or unsuitable detergent (creates  
too much foam) has been used.  
• Reduce the detergent quantity or use another one.  
Check whether there are any leaks from one of the  
inlet hose fittings. It is not always easy to see this as  
the water runs down the hose; check to see if it is  
damp.  
There is water on the floor:  
• Check the water inlet hose connection.  
The inlet hose is damaged.  
• Change it with a new one.  
The cap on the emergency emptying hose has not  
been replaced after cleaning the pump.  
Put the cap back on the emergency emptying and  
place the latter back in its seat.  
Too little detergent or unsuitable detergent has been  
used.  
• Increase the detergent quantity or use another one.  
Stubborn stains have not been treated prior to  
washing.  
• Use commercial products to treat the stubborn  
stains.  
Unsatisfactory washing results:  
The correct temperature was not selected.  
• Check if you have selected the correct  
temperature.  
Excessive laundry load.  
• Introduce into the drum less laundry.  
 
20  
Malfunction  
Possible Cause / Solution  
The programme is still running.  
• Wait the end of washing cycle.  
The door lock has not been released.  
• Wait about 2 minute.  
The door will not open:  
There is water in the drum.  
• Select drain or spin programme to empty out the  
water.  
The transit bolts and packing have not been  
removed.  
• Check the correct installation of the appliance.  
The support feet have not been adjusted.  
• Check the correct levelling of the appliance.  
The machine vibrates or is noisy:  
The laundry is not evenly distributed in the drum.  
• Redistribute the laundry.  
Maybe there is very little laundry in the drum.  
• Load more laundry.  
The electronic unbalance detection device has cut in  
because the laundry is not evenly distributed in the  
drum. The laundry is redistributed by reverse rotation  
of the drum. This may happen several times before  
the unbalance disappears and normal spinning can  
resume. If, after 10 minutes, the laundry is still not  
evenly distributed in the drum, the machine will not  
spin. In this case, redistribute the load manually and  
select the spin programme.  
Spinning starts late or the machine  
does not spin:  
Redistribute the laundry.  
The machine is fitted with a type of motor which  
makes an unusual noise compared with other  
traditional motors. This new motor ensures a softer  
start and more even distribution of the laundry in the  
drum when spinning, as well as increased stability of  
the machine.  
The machine makes an unusual noise  
No water is visible in the drum  
Machines based on modern technology operate very  
economically using very little water without affecting  
performance.  
If you are unable to identify or solve the  
problem, contact our service centre.  
Before telephoning, make a note of the model,  
serial number and purchase date of your  
machine: the Service Centre will require this  
information.  
Mod. ... ... ...  
Prod. No. ... ... ...  
Ser. No. ... ... ...  
 
21  
Technical data  
Dimensions  
Width  
60 cm  
85 cm  
63 cm  
Height  
Depth (inclunding the porthole)  
Electrical connection Voltage -  
Overall power - Fuse  
Information on the electrical connection is given on the rating  
plate on the inner edge of the appliance door  
Water supply pressure  
Maximum Load  
Minimum  
Maximum  
0,05 MPa  
0,8 MPa  
Cotton  
Synthetics  
Delicates  
Woollens and handwash  
6
kg  
kg  
kg  
kg  
3
3
2
Spin Speed  
Maximum  
0
1000 rpm (ZWF 10070 W)  
1200 rpm (ZWF 12070 W - S)  
1400 rpm (ZWF 14070 W)  
1600 rpm (ZWF 16070 W - S)  
 
22  
Consumption values  
Programme  
Programme  
duration  
(in minutes)  
Energy  
consumption  
(in kWh)  
Water  
consumption  
(in litres)  
Cottons 95°C  
125  
155  
100  
145  
80  
2.0  
1.02  
1.3  
61  
54  
58  
54  
51  
60  
60  
53  
53  
55  
47  
Cottons 60° Eco(*)  
Cottons 60°C - 40°C  
Cottons 40°C Eco  
Synthetics 50°C - 40°C  
Synthetics Easy Iron 40°C  
Delicates 40°C - 30°C  
Wool 40°C  
1.14  
0.8  
90  
0.35  
0.55  
0.4  
55  
60  
Handwash 40°  
60  
0.4  
Mini 30’  
30  
0.25  
0.2  
Silk 30°C  
30  
Sport Shoes 40°C  
Sport 40°C  
Rinse  
65  
100  
45  
2
0.5  
0.65  
0.1  
-
60  
59  
42  
-
Drain  
Spin  
10  
-
-
Infos  
The consumption data shown on this chart is to  
be considered purely indicative, as it may vary  
depending on the quantity and type of laundry,  
on the inlet water temperature and on the  
ambient temperature. It refers to the highest  
temperature for each wash programme.  
(*) The “Cottons 60° Eco” is the reference  
programme for the data entered in the  
energy label, in compliance with EEC 92/75  
standards.  
 
23  
Installation instruction  
Unpacking  
All transit bolts and packing must be removed  
before using the appliance.  
5. Remove the bracket D, refit the six smaller  
bolts C and slide out the relevant plastic  
spacer E.  
You are advised to keep all transit devices so  
that they can be refitted if the machine ever  
has to be transported again.  
6. Open the porthole, take out the inlet hose  
from the drum and remove the polystyrene  
block fitted with the adhesive tape on the  
door seal.Open the porthole, take out the  
inlet hose from the drum and remove the  
polystyrene block fitted with the adhesive  
tape on the door seal.  
7. Fill the smaller upper hole and the two large  
ones with the corresponding plastic plug  
caps supplied in the bag containing the  
instruction booklet.  
1. After removing all the packaging, carefully  
lay machine on it’s back to remove the  
polystyrene base from the bottom.  
2. Remove the power supply cable and the  
draining hose from the hose holders on the  
rear of the appliance.  
Positioning  
A
Install the machine on a flat hard floor. Make  
sure that air circulation around the machine is  
not impeded by carpets, rugs etc. Check that  
the machine does not touch the wall or other  
kitchen units. Level the washing machine by  
raising or lowering the feet. The feet may be  
tight to adjust as they incorporate a self locking  
nut, but the machine MUST be level and  
stable.  
C
B
B
C
3. With a suitable spanner unscrew and  
remove the central rear bolt A.  
4. Unscrew and remove the two large rear  
bolts B and the six smaller bolts C.  
If necessary, check the setting with a spirit  
level.  
Any necessary adjustment can be made with a  
spanner.  
Accurate levelling prevents vibration, noise and  
displacement of the machine during  
operation.Never place cardboard, wood or  
similar materials under the machine to  
compensate for any unevenness in the floor.  
E
C
D
C
 
24  
The appliance must be connected to a cold  
water supply.  
A minimum water pressure of 0.05 MPa (0.5  
bar) is required for safe operation of the  
appliance.  
If you cannot make the cold water connection  
direct from the rising mains, you may be able  
to operate the appliance from your cold water  
storage system.  
There should be a minimum distance of 5.02m  
(16.5 ft) between the appliance’s inlet and the  
bottom of the water storage tank.  
Water inlet  
An inlet hose is supplied and can been found  
inside the machine drum.  
Do not use the hose from your previous  
machine to connect to the water supply.  
Water drainage  
This appliance is designed to be permanently  
plumbed into your home's drainage system  
using one of the following methods.  
1. Open the porthole and extract the inlet  
hose.  
2. Connect the hose with the angled  
connection to the machine.  
Do not place the inlet hose downwards.  
Angle the hose to the left or right depending  
on the position of your water tap.  
1. Into a drainage standpipe.  
3. Set the hose  
correctly by loosening  
the ring nut.  
U” piece  
supplied  
After positioning the  
inlet hose, be sure to  
tighten the ring nut  
again to prevent leaks.  
Special  
Off  
Cottons  
S
p
o
r
t
4
0
°
95°  
3h  
6h  
9h  
S
p
o
r
t
S
h
o
e
s
4
0
°
60° Eco  
60°  
1000  
900  
Silk  
M
i
n
i
3
0
'
4
0
°
E
c
o
700  
Prewash  
Intensive  
Wash  
Door  
End  
Cold  
Hand  
40°  
Synthetics  
50°  
Super  
Quick  
Wash  
30°  
ool  
1
0
0
0
6
k
g
Options  
E
x
t
r
a
R
i
n
s
e
Start/Pause  
Spin  
W
40°  
aIron 40°  
Spin  
Drain  
40°  
R
i
n
s
e
3
0
°
ZWF10070W  
Delicates  
38 mm (11.2”)  
standpipe  
diameter  
4. Connect the hose to a tap with a 3/4” thread.  
Always use the hose supplied with the  
appliance. The inlet hose must not be  
lengthened. If it is too short and you do not  
wish to move the tap, you will have to  
purchase a new, longer hose specially  
designed for this type of use.  
Firstly form a hook in the end of the drain  
hose using the «U» piece supplied. Place the  
drain hose into your standpipe, which should  
have an internal diameter of approximately  
38mm thus ensuring there is an air break  
between the drain hose and standpipe.  
When discharging into a standpipe ensure that  
the top of the standpipe is no more than 90  
cm (35.4'') and no less than 60 cm (23.6'')  
above floor level.  
NOTE  
Installation should  
comply with local  
water authority and  
building regulations’  
requirements.  
 
25  
Levelling  
Level the washing machine by raising or  
lowering the feet. The feet may be tight to  
adjust as they incorporate a self locking nut,  
but the machine MUST be level and stable.  
Special  
Spor  
t
40°  
Off  
95°  
Cottons  
3h  
6h  
9h  
Spor  
t
S
h
o
e
s
4
0
°
60° Eco  
60°  
1000  
900  
Silk  
Mini 30'  
Cold  
4
0
°
E
c
o
700  
Prewash  
Intensive  
Wash  
Door  
End  
40°  
Hand  
Synthetics  
50°  
Super  
Quick  
W
ash  
1
0
0
0
6
k
g
30°  
ool  
Spin  
Options  
E
x
t
r
a
R
i
n
s
e
Start/Pause  
W
40°  
Easy Iron 40°  
Spin  
Drain  
40°  
Rinse 30° Delicates  
ZWF10070W  
Any necessary  
adjustment can be  
made with a spanner.  
Accurate levelling  
prevents vibration,  
noise and  
displacement of the  
The drain hose may be extended to a  
maximum of 4 metres. An additional drain hose  
and joining piece is available from your local  
Service Force Centre. The joining piece must  
have an internal diameter of 18mm.  
machine during operation.  
Some vibration is inevitable, especially if  
mounted on a wooden floor.  
Sprung wooden floors are particularly  
susceptible to vibration. For advice, consult a  
builder. If possible, always place the machine  
on a solid floor.  
If your drain hose  
looks like this (see  
below) you do not  
require the «U» piece.  
Just push the hose  
firmly into the  
standpipe.  
Special conditions  
2. Onto a sink outlet spigot.  
If the outlet spigot has not been used before,  
remove any blanking plug that may be in place.  
If the floor is carpeted or covered with crumbly  
or soft material, insert a rigid support base  
under the feet to prevent noise, vibration or  
displacement. The base should protrude a few  
centimetres beyond the edges of the machine.  
WARNING!  
The machine should NOT be placed on deep  
pile carpeting.  
Loop  
NOTE  
Please ensure that when the appliance is  
installed it is easily accessible for the engineer  
in the event of a breakdown.  
Push the drain hose onto the spigot and secure  
with a clip if required, ensure a loop is formed  
in the drain hose (see diagram) to prevent  
waste from the sink entering the washing  
machine.  
In the interest of the environment  
Washing machines and dishwashers should be  
connected to the FOUL drainage system, the  
water will then be taken to a sewage works for  
treatment before being discharged safely into a  
river. It is essential that these appliances are  
not connected to the surface water drainage  
system as this water is discharged directly into  
a river or stream and may cause pollution.  
Important!  
Before connecting the machine to new  
pipework or to pipework that has not been  
used for some time, run off a reasonable  
amount of water to flush out any debris that  
may have collected in the pipes.  
 
26  
If you require any further advice please  
contact your local water authority.  
The wires in the mains lead are coloured in  
accordance with the following code:  
Green and Yellow ..............................- Earth  
Blue ....................................................- Neutral  
Brown..................................................- Live  
The wire coloured green  
GREEN &YELLOW  
SHOWER  
and yellow must be  
connected to the  
E
SINK TOILET  
BATH  
BIDET  
terminal marked with  
L
N
the letter «E» or by the  
WASHING  
MACHINE  
DISHWASHER  
earth symbol  
or  
RAINWATER  
'RUN-OFF'  
BROWN  
coloured green and  
yellow.  
BLUE  
FOUL DRAIN  
CORD CLAMP  
SURFACE WATER  
SEWERS  
FOUL SEWERS  
DRAINS  
&
SEWAGE  
TREATMENT  
WORKS  
UNTREATED  
DISCHARGE  
The wire coloured blue must be connected to  
the terminal marked «N» or coloured black.  
TREATED  
DISCHARGE  
RIVER  
RIVER  
The wire coloured brown must be connected to  
the terminal marked «L» or coloured red.  
Upon completion there must be no cut, or stray  
strands of wire present and the cord clamp  
must be secure over the outer sheath.  
Electrical connection  
Any electrical work required to install this  
appliance should be carried out by a qualified  
electrician or competent person.  
WARNING!  
WARNING!  
A cut off plug inserted into a 13 amp socket  
is a serious safety (shock) hazard.  
Ensure that the cut off plug is disposed of  
safely. Should the appliance power supply  
cable need to be replaced, this must be  
carried out by our Service Force Centre.  
This appliance must be earthed.  
The manufacturer declines any liability  
should this safety measure not be  
observed.  
Before switching on, make sure the electricity  
supply voltage is the same as that indicated  
on the appliance’s rating plate.  
The power supply cable must be easily  
accessible after installing the appliance.  
IMPORTANT!  
Permanent connection  
Information on the electrical connection is  
given on the rating plate on the inner edge  
of the appliance door.  
In the case of permanent connection it is  
necessary that you install a double pole switch  
between the appliance and the electricity  
supply (mains), with a minimum gap of 3mm  
between the switch contacts and of a type  
suitable for the required load in compliance  
with the current electrical regulations.  
The switch must not break the yellow and  
green earth cable at any point.  
The appliance is supplied with a 13amp plug  
fitted. In the event of having to change the  
fuse in the plug supplied, a 13amp ASTA  
approved (BS1363/A) fuse must be used.  
Should the plug need to be replaced for any  
reason, proceed as described below.  
 
27  
Environmental concerns  
Packaging materials  
Ecological hints  
The materials marked with the symbol  
recyclable.  
>PE<=polyethylene  
>PS<=polystyrene  
>PP<=polypropylene  
This means that they can be recycled by  
disposing of them properly in appropriate  
collection containers.  
are  
To save water, energy and to help protect the  
environment, we recommend that you follow  
these tips:  
Normally soiled laundry may be washed  
without prewashing in order to save  
detergent, water and time (the environment  
is protected too!).  
The machine works more economically if it is  
fully loaded.  
Old machine  
Use authorised disposal sites for your old  
appliance. Help to keep your country tidy!  
With adequate pre-treatment, stains and  
limited soiling can be removed; the laundry  
can then be washed at a lower temperature.  
Measure out detergent according to the  
water hardness, the degree of soiling and  
the quantity of laundry being washed.  
The symbol  
on the product or on its  
packaging indicates that this product may not  
be treated as household waste. Instead it shall  
be handed over to the applicable collection  
point for the recycling of electrical and  
electronic equipment. By ensuring this product  
is disposed of correctly, you will help prevent  
potential negative consequences for the  
environment and human health, which could  
otherwise be caused by inappropriate waste  
handling of this product. For more detailed  
information about recycling of this product,  
please contact your local city office, your  
household waste disposal service or the shop  
where you purchased the product.  
 
28  
Guarantee conditions  
Standard guarantee conditions  
Service and Spare Parts.  
We, Zanussi-Electrolux, undertake that if  
within12 months of the date of the purchase  
this Zanussi-Electrolux appliance or any part  
thereof is proved to be defective by reason  
only of faulty workmanship or materials, we  
will, at our option repair or replace the same  
FREE OFCHARGE for labour, materials or  
carriage on condition that:  
In the event of your appliance requiring  
service, or if you wish to purchase spare parts,  
please contact your local Service Force Centre  
by telephoning:  
0870 5 929 929  
Your telephone call will be automatically routed  
to the Service Force Centre covering your  
postcode area. For the address of your local  
Service Force Centre and further information  
about Service Force, please visit the website at  
The appliance has been correctly  
installedand used only on the electricity  
supply statedon the rating plate.  
The appliance has been used for normal  
domestic purposes only, and in accordance  
with the manufacturer's instructions.  
The appliance has not been serviced,  
maintained, repaired, taken apart or  
tampered with by any person not authorised  
by us.  
Before calling out an engineer, please ensure  
you have read the details under the heading  
«Something not working». When you contact  
the Service Force Centre you will need to give  
the following details:  
1 Your name, address and postcode.  
2 Your telephone number.  
Electrolux Service Force Centre must  
undertake all service work under this  
guarantee.  
3 Clear concise details of the fault.  
Any appliance or defective part replaced  
shall become the Company's property.  
This guarantee is in addition to your  
statutoryand other legal rights.  
4 The model and Serial number of the  
appliance (found on the rating plate).  
5 The purchase date.  
Please note a valid purchase receipt or  
guarantee documentation is required for in  
guarantee service calls.  
Exclusions  
Damage or calls resulting fromtransportation,  
improper use or neglect, thereplacement of  
any light bulbs or removableparts of glass or  
plastic.  
Costs incurred for calls to put right an  
appliance which is improperly installed or  
calls to appliances outside the United  
Kingdom.  
Customer Care  
For general enquiries concerning your  
Electrolux appliance, or for further information  
on Electrolux products please contact our  
Customer Care Department by letter or  
telephone at the address below or visit our  
Appliances found to be in use within  
acommercial environment, plus those which  
are subject to rental agreements.  
Products of Electrolux manufacturer that are  
not marketed by Electrolux.  
Customer Care Department Electrolux Major  
Appliances Addington Way Luton Bedfordshire,  
LU4 9QQ Tel: 08705 727 727 (*)  
(*) Calls may be recorded for training purposes  
 
29  
For Customer Service in The Republic of  
Ireland please contact us at the address below:  
Electrolux Group (Irl) Ltd  
Long Mile Road, Dublin 12, Republic of Ireland  
Tel: + 353 (0)1 4090751  
European guarantee  
This appliance is guaranteed by Electrolux, in  
each of the countries listed in the following  
page, for the period specified in the appliance  
guarantee or otherwise by law. If you move  
from one of these countries to another of these  
countries the appliance guarantee will move  
with you subject to the following qualifications:  
The appliance guarantee starts from the  
date you first purchased the appliance  
which will be evidenced by production of a  
valid purchase document issued by seller  
of the appliance.  
The appliance guarantee is for the same  
period and to the same extent for labour  
and parts as exists in your country of  
residence for this particular model or range  
of appliances.  
The appliance guarantee is personal to the  
original purchaser of the appliance and  
cannot be transferred to another user.  
The appliance is installed and used in  
accordance with instructions issued by  
Electrolux and is only used within the  
home, i.e. is not used for commercial  
purposes.  
The appliance is installed in accordance  
with all relevant regulations in force within  
your new country of residence.  
The provisions of this European Guarantee do  
not affect any of the rights granted to you by  
law.  
 
30  
à
Albania  
+35 5 4 261 450  
+32 2 363 04 44  
+420 2 61 12 61 12  
+45 70 11 74 00  
+49 180 32 26 622  
+37 2 66 50 030  
+34 902 11 63 88  
+44 8705 929 929  
+30 23 10 56 19 70  
+38 51 63 23 338  
+353 1 40 90 753  
+39 (0) 434 558500  
+37 17 84 59 34  
+370 5 27 80 609  
+35 2 42 43 13 01  
+36 1 252 1773  
Rr. Pjeter Bogdani Nr. 7 Tirane  
Belgique/België/Belgien  
Česká republika  
Danmark  
Bergensesteenweg 719, 1502 Lembeek  
Budějovická 3, Praha 4, 140 21  
Sjællandsgade 2, 7000 Fredericia  
Deutschland  
Muggenhofer Str. 135, 90429 Nürnberg  
Mustamäe tee 24, 10621 Tallinn  
Eesti  
España  
Carretera M-300, Km. 29,900 Alcalá de Henares Madrid  
France  
Great Britain  
Hellas  
Addington Way, Luton, Bedfordshire LU4 9QQ  
4, Limnou Str., 54627 Thessaloniki  
Hrvatska  
Ireland  
Slavonska avenija 3, 10000 Zagreb  
Longmile Road Dublin 12  
Italia  
C.so Lino Zanussi, 26 - 33080 Porcia (PN)  
Kr. Barona iela 130/2, LV-1012, Riga  
Verkiu,2 9, 09108 Vilnius, Lithuania  
Rue de Bitbourg, 7, L-1273 Hamm  
Latvija  
Lituania  
Luxembourg  
Magyarország  
Nederland  
Norge  
H-1142 Budapest XIV, Erzsébet királyné útja 87  
Vennootsweg 1, 2404 CG - Alphen aan den Rijn  
Risløkkvn. 2 , 0508 Oslo  
+31 17 24 68 300  
+47 81 5 30 222  
+43 18 66 400  
Österreich  
Polska  
Herziggasse 9, 1230 Wien  
+48 22 43 47 300  
+35 12 14 40 39 39  
+40 21 451 20 30  
ul. Kolejowa 5/7, Warsaw  
Portugal  
Romania  
Quinta da Fonte - Edificio Gonçalves Zarco - Q35 -2774-518 Paço de Arcos  
Str. Garii Progresului 2, S4, 040671 RO  
Industriestrasse 10, CH-5506 Mägenwil  
Tr aška 132, 1000 Ljubljana  
Schweiz-Suisse-Svizzera +41 62 88 99 111  
Slovenija  
Slovensko  
Suomi  
+38 61 24 25 731  
+421 2 43 33 43 22  
Electrolux Slovakia s.r.o., Electrolux Domáce spotrebiče SK, Seberíniho 1, 821 03 Bratislava  
Sverige  
Türkiye  
+46 (0)771 76 76 76  
+90 21 22 93 10 25  
+7 095 937 7837  
Electrolux Service, S:t Göransgatan 143, S-105 45 Stockholm  
Tarlabași caddesi no : 35 Taksim Istanbul  
Россия  
129090 Москва, Олимпийский проспект, 16, БЦ “Олимпик”  
 
31  
 
Subject to change without notice  
132973860  

West Bend Oven L5659B User Manual
Whirlpool Double Oven RBS305PV User Manual
Whirlpool Freezer EEV 202X User Manual
Whirlpool Range 9763001 User Manual
Whirlpool Range WFG361LV User Manual
Whirlpool Washer Dryer LA3800XM User Manual
Woods Equipment TV Mount 1012606 User Manual
Zanussi Clothes Dryer TD164 User Manual
Zanussi Refrigerator ZU 9124 User Manual
Zenoah Brush Cutter BC3401FW User Manual