U
AX-497/AX-397
Stereo Amplifier
OWNER’S MANUAL
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
1
2
3
4
5
6
7
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
8
9
•
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
10 Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
IMPORTANT
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
13 Unplug this apparatus during lightning storms or when
unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is
often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group
recommend you to avoid prolonged exposure from excessive volume levels.
i
IMPORTANT SAFETY INSTRUCTIONS
FCC INFORMATION (for US customers)
1
IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
Relocate either this product or the device that is being
affected by the interference.
2
3
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to the
operation of other electronic devices.
ii
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install this sound system in a well ventilated, cool, dry, clean
place – away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold. Allow ventilation space of at least
30 cm on the top, 20 cm on the left and right, and 20 cm on
the back of this unit.
14 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the wall
outlet.
15 Install this unit near the AC outlet and where the AC power
plug can be reached easily.
16 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
3
4
Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
17 Before moving this unit, press STANDBY/ON to set this unit
in the standby mode, and disconnect the AC power plug from
the wall outlet.
Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
Avoid installing this unit where foreign objects may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
18 VOLTAGE SELECTOR (Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE plugging
into the AC main supply. Voltages are:
5
General model.............AC 110/120/220/230–240 V, 50/60 Hz
Asia model ................................AC 220/230–240 V, 50/60 Hz
–
–
–
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
As long as this unit is connected to the AC wall outlet,
it is not disconnected from the AC power source even
if you turn off this unit by POWER or set it to the
standby mode by STANDBY/ON.
6
Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7
8
9
Do not plug in this unit to a wall outlet until all connections
are complete.
This unit enters the standby mode when you press
POWER inward to the ON position and then press
STANDBY/ON. In this state, this unit is designed to
consume a very small quantity of power.
Do not operate this unit upside-down. It may overheat,
possibly causing damage.
Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury.
YAMAHA will not be held responsible for any damage
resulting from use of this unit with a voltage other than
specified.
POUR LES CONSOMMATEURS CANADIENS
Pour éviter les chocs électriques, introduire la lame la
plus large de la fiche dans la borne correspondante de
la prise et pousser jusqu’au fond.
Cet appareil numérique de la classe B est conforme à
la norme NMB-003 du Canada.
13 Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed. The
cabinet should never be opened for any reasons.
iii
CONTENTS
INTRODUCTION
PREPARATION
OPERATION
ADDITIONAL INFORMATION
1
FEATURES
FEATURES
◆ Highly dynamic power, low impedance drive
capability
◆ Continuously variable loudness control
◆ CD/DVD DIRECT AMP switch used to reproduce the
purest CD and DVD sound
[ AX-497 ]
◆ Minimum RMS output power
85 W + 85 W (8 Ω), 0.019% THD, 20 Hz to 20 kHz
◆ REC OUT selector independent of input source
selection
◆ Remote control capability
◆ PURE DIRECT switch used to reproduce the purest
source sound
[ AX-397 ]
◆ Minimum RMS output power
60 W + 60 W (8 Ω), 0.019% THD, 20 Hz to 20 kHz
◆ TAPE MONITOR switch used to monitor the sound
being recorded
• This document is the owner’s manual for both AX-497 and AX-397. Model names are given where the details of functions are unique
to each model. Illustrations for AX-497 are mainly used for explanations.
• y indicates a tip for your operation.
• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button
names differ between the main unit and the remote control, the names of the buttons on the remote control are given in parentheses.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In
case of differences between the manual and the product, the product has priority.
SUPPLIED ACCESSORIES
Please check that you received all of the following parts.
Remote control
POWER
Batteries (2)
(AAA, R03, UM-4)
STANDBY
CD/DVD PHONO
TUNER
AUX
MD
TAPE
u
+
PRESET
d
VOLUME
–
A/B/C/D/E
A/B
DISPLAY
w
e
f
DISPLAY
DIR
A
DIR
B
REC
b
s
a
DISC
CD TAPE
p
2
CONTROLS AND FUNCTIONS
CONTROLS AND FUNCTIONS
Front panel
■ AX-497
12
3
4
5
6
8
STANDBY
POWER
AUX
MD
TAPE
CD/DVD
TUNER
PHONO
PURE DIRECT
CD/DVD DIRECT AMP
ON
OFF
16
20
12
VOLUME
INPUT
26
8
PHONES
SPEAKERS
BASS
TREBLE
BALANCE
LOUDNESS
REC OUT
DISPLAY
FLAT
CD/DVD
1
1
1
1
1
1
1
TAPE
MD
AUX
TUNER
PHONO
–
30dB
A
B
40
4
2
2
4
2
4
2
4
2
2
2
4
10
STANDBY
/ON
3
3
3
3
3
3
3
9
4
4
4
8
ON
OFF
–
5
5
+
–
5
5
+
L
5
5
R
5
7
60
2
6
0
∞
-dB
9
0
A
B
C
D
E
F
■ AX-397
12
3
4
5
7
8
STANDBY
POWER
AUX
MD
TAPE
CD/DVD
TUNER
PHONO
TAPE MONITOR
CD/DVD DIRECT AMP
ON
OFF
16
20
12
VOLUME
26
8
INPUT
PHONES
SPEAKERS
BASS
TREBLE
BALANCE
LOUDNESS
DISPLAY
FLAT
1
1
1
1
1
1
1
–
30dB
A
B
40
4
2
2
2
4
2
4
2
2
2
4
10
STANDBY
/ON
3
3
3
3
3
3
3
9
8
4
4
4
4
ON
OFF
–
5
5
+
–
5
5
+
L
5
5
R
5
7
60
2
6
0
∞
-dB
9
0
A
B
C
D
F
1 POWER
2 STANDBY indicator
Press inward to the ON position to provide this unit with
power supply from the AC wall outlet. In this state, you
can turn on this unit or set it to the standby mode by
pressing STANDBY/ON.
Lights up when this unit is in the standby mode.
3 STANDBY/ON
Turns on this unit or sets it to the standby mode.
When you turn on this unit, there will be a few second
delay before this unit can reproduce sound.
Press again to release it outward to the OFF position to
Notes
• This switch is operational only when POWER is pressed inward
to the ON position.
• In the standby mode, this unit consumes a small amount of
power to receive infrared-signals from the remote control.
completely cut off power supply from the AC wall outlet.
3
CONTROLS AND FUNCTIONS
4 Remote control sensor
0 SPEAKERS A/B
Receives signals from the remote control.
Turns on or off the speaker set connected to the
SPEAKERS A and/or B terminals on the rear panel each
time the corresponding button is pressed.
5 INPUT selector and indicators
Selects the input source you want to listen to.
The input source indicators light up when the
corresponding input sources are selected.
A BASS
Increases or decreases the low frequency response. The 0
position produces a flat response.
See page 13 for details.
6 PURE DIRECT and indicator
(AX-497 only)
Allows you to listen to a source in the purest possible
sound.
The indicator above it lights up when this function is
turned on.
B TREBLE
Increases or decreases the high frequency response. The 0
position produces a flat response.
See page 13 for details.
C BALANCE
7 TAPE MONITOR and indicator
(AX-397 only)
Allows you to listen to the sound played back on the tape
deck connected to the TAPE terminals on the rear panel of
this unit.
When the tape deck is used for recording, you can also
monitor the sound being recorded.
The indicator above it lights up when this function is
turned on.
Adjusts the sound output balance of the left and right
speakers to compensate for sound imbalances caused by
speaker locations or listening room conditions.
See page 13 for details.
D LOUDNESS
Retains a full tonal range at any volume level to
compensates for the human ears’ loss of sensitivity to high
and low-frequency ranges at low volume.
See page 13 for details.
Notes
E REC OUT selector
• When this function is on (the indicator lights up), TAPE (tape
deck) cannot be selected with the INPUT selector.
• To listen to the source selected with the INPUT selector, press
again to turn off the function (the indicator turns off as a result).
• When TAPE (tape deck) is selected with the INPUT selector,
this function will not turn on even if TAPE MONITOR is
pressed.
(AX-497 only)
Selects a source for recording to the MD recorder or the
tape deck independently of the INPUT selector setting,
allowing you to record the selected source while listening
to another source.
See page 14 for details.
F VOLUME
Controls the sound output level.
This does not affect the REC OUT level.
8 CD/DVD DIRECT AMP and indicator
Allows you to listen to a CD or a DVD source in the
purest sound.
The indicator above it lights up when this function is
turned on.
■ Opening and closing the front panel
door
When you want to use the controls behind the front panel
door, open the door by gently pressing on the lower part of
the panel. Keep the door closed when not using these
controls to protect the controls from dust, etc.
9 PHONES jack
Outputs audio for private listening with headphones.
Press both SPEAKERS A and B switches on the front
panel to release them outward to the OFF position.
4
CONTROLS AND FUNCTIONS
Remote control
This section describes the function of each control on the
remote control used to control this unit or a YAMAHA
CD player, tuner, tape deck, etc. with the remote control
capability.
■ Controlling this unit
1 Infrared signal transmitter
Sends signals to this unit.
2 POWER
Turns on this unit.
Note
Some components may not be controlled by this remote control.
Note
1
This button is operational only when POWER on the front panel
is pressed inward to the ON position.
POWER
3 STANDBY
2
STANDBY
Sets this unit to the standby mode.
CD/DVD PHONO
TUNER
AUX
3
4
Notes
MD
TAPE
• This button is operational only when POWER on the front
panel is pressed inward to the ON position.
• In the standby mode, this unit consumes a small amount of
power in order to receive infrared-signals from the remote
control.
u
+
PRESET
d
VOLUME
5
6
4 Input selector buttons
Select the input source you want to listen to.
–
A/B/C/D/E
5 VOLUME +/–
Controls the sound output level.
This does not affect the REC OUT level.
A/B
DISPLAY
w
e
f
DISPLAY
7
8
DIR A
DIR B
REC
DISC
b
s
a
■ Controlling other components
The functions of the buttons to control other YAMAHA
components are the same as those of the corresponding
buttons on those components. Refer to those components’
instruction manuals for details.
CD TAPE
p
6 Tuner buttons
Control various functions of the tuner.
PRESET +/–
Selects a preset station number (1 to 8).
A/B/C/D/E
Selects a preset station group (A to E).
7 CD player / tape deck buttons
Control various functions of the CD player or the tape
deck.
Notes
• DIR B and A/B apply only to the double cassette tape deck.
• Pressing DIR A will reverse the tape direction on the single
cassette tape deck with the automatic reverse function.
8 CD/TAPE selector switch
Switches to control either CD player functions or tape
deck functions.
5
CONTROLS AND FUNCTIONS
Installing batteries in the remote
control
Using the remote control
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the front panel of this unit during
operation.
1
3
STANDBY
POWER
AUX
MD
TAPE
CD/DVD
TUNER
PHONO
PURE DIRECT
CD/DVD DIRECT AMP
ON
OFF
16
20
12
VOLUME
INPT
26
8
2
PHONES
SPEAKERS
BASS
TREBLE
BALANCE
LOUDNESS
REC OUT
FLAT
CD/DVD
1
1
1
1
1
1
1
T
APE
MD
AUX
TUNER
PHONO
A
B
–
30dB
2
2
4
2
4
2
4
2
2
2
10
40
4
STANDBY
/ON
3
3
3
3
3
3
3
9
8
4
4
4
4
ON
OFF
–
5
5
+
–
5
5
+
L
5
5
R
5
7
6
60
2
∞
0
-dB
Approximately 6 m (19.7 ft)
30
30
POWER
C
D
/
D
V
D
P
H
O
N
O
TUNER
STANDBY
MD
TAPE
AUX
1
Open the battery compartment cover.
u
+
PRESET
d
VOLUME
–
A/B/C/D/E
MUTE
A/B
DISPLA
Y
w
e
f
DISPLAY
DIR
A
DIR
B
REC
b
s
a
DISC
CD
TAPE
p
2
Insert two supplied batteries
(AAA, R03, UM-4) according to the polarity
markings (+ and –) on the inside of the
battery compartment.
■ Handling the remote control
•
The area between the remote control and this unit must
be clear of large obstacles.
•
Do not spill water or other liquids on the remote
control.
Do not drop the remote control.
Do not leave or store the remote control in the
following types of conditions:
– places of high humidity, such as near a bath
– places of high temperature, such as near a heater or
a stove
3
Close the cover back.
•
•
■ Notes on batteries
• Change all of the batteries if you notice the following
conditions; the operation range of the remote control decreases,
the indicator does not flash or its light becomes dim.
• Use AAA, R03, UM-4 batteries.
• Make sure that the polarities are correct. See the illustration
inside the battery compartment.
• Remove the batteries if the remote control is not used for an
extended period of time.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
– places of extremely low temperatures
– dusty places
•
Do not expose the remote control sensor to strong
lighting, in particular, an inverter type fluorescent
lamp; otherwise, the remote control may not work
properly. If necessary, position this unit away from
direct lighting.
• We strongly recommend using alkaline batteries.
• If the batteries have leaked, dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before
installing new batteries.
• Do not throw away batteries with general house waste; dispose
of them correctly in accordance with your local regulations.
6
CONTROLS AND FUNCTIONS
Rear panel
1
2
3
4
TUNER
IN
(PLAY)
SPEAKERS
AC OUTLETS
+
–
–
+
TAPE
OUT
(REC)
IMPEDANCE SELECTOR
PHONO
A
B
IN
GND
(PLAY)
A
OR B: 4ΩMIN
A+B: 8ΩMIN
/
/
SPEAKER
SPEAKER
MD
OUT
(REC)
AUX
CD/DVD
SWITCHED
100W MAX.TOTAL
A
OR B: 6ΩMIN SPEAKER
/
(U.S.A. model)
5
6
1 PHONO jacks and GND terminal
See page 8 for connection information.
■ IMPEDANCE SELECTOR switch
CAUTION
2 Audio input/output jacks
See page 8 for connection information.
Do not change the IMPEDANCE SELECTOR switch
while the power of this unit is turned on, as doing so may
damage the unit.
3 AC OUTLET(S)
Use to supply power to your other audio/video
components.
If this unit fails to turn on, the IMPEDANCE SELECTOR
switch may not be fully slid to either position. If this is the
case, slide the switch all the way to either position when
this unit’s power supply is completely cut off.
Select the switch position (left or right) according to the
impedance of the speakers in your system.
4 AC power supply cord
See page 10 for connection information.
5 SPEAKERS terminals
Connect one or two speaker sets.
See page 8 for connection information.
Switch
Impedance level
position
Asia model
6 IMPEDANCE SELECTOR
See “IMPEDANCE SELECTOR switch” on this page.
• If you use one set (A or B), the impedance of
each speaker must be 8 Ω or higher.
• If you use two sets (A and B), the impedance
of each speaker must be 16 Ω or higher.
■ Asia and General models only
VOLTAGE SELECTOR is only applicable to the Asia and
Canada model
General models.
• You can use one set (A or B), and the
impedance of each speaker must be 6 Ω or
higher.
Right
VOLTAGE SELECTOR
Other models
• If you use one set (A or B), the impedance of
each speaker must be 6 Ω or higher.
• If you use two sets (A and B), the impedance
of each speaker must be 12 Ω or higher.
• If you use one set (A or B), the impedance of
each speaker must be 4 Ω or higher.
• If you use two sets (A and B), the impedance
Left
of each speaker must be 8 Ω or higher.
7
CONNECTIONS
CONNECTIONS
Connecting speakers and other components
CAUTION
•
•
•
Do not connect this unit or other components to the main power until all connections between components are
complete.
Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could
damage this unit and/or the speakers.
All connections must be correct: L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty,
no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be
unnatural and lack bass. Also, refer to the owner’s manual for each of your components.
Use RCA type pin plug cables for audio/video units except speakers.
Connect your turntable to the GND terminal to reduce noise in the signal. However, you may hear less noise without
the connection to the GND terminal for some record players.
•
•
•
Turntable
Tuner
Tape deck, etc.
Speakers A
Audio out
Audio out
Audio out
Audio in
R
L
R
L
R
L
+
–
–
+
GND
R
L
TUNER
IN
(PLAY)
SPEAKERS
+
–
–
+
TAPE
OUT
(REC)
PHONO
A
B
IN
GND
(PLAY)
MD
OUT
(REC)
AUX
CD/DVD
+
–
–
+
R
L
R
L
R
R
L
L
Audio out
Audio out
Audio in
Audio out
CD player or
DVD player
VCR, etc.
MD recorder,
etc.
Speakers B
8
CONNECTIONS
■ Connecting the banana plug
1
Remove approximately 10 mm (3/8 in) of
insulation from the end of each speaker
cable and twist the exposed wires of the
cable together to prevent short circuits.
(With the exception of Asia, Korea, U.K. and
Europe models)
First, tighten the knob and then insert the banana plug into
the end of the corresponding terminal.
10 mm (3/8 in)
Banana plug
2
3
Unscrew the knob.
Notes
• One or two speaker sets can be connected to this unit. If you use
only one speaker set, connect it to either the SPEAKERS A or B
terminals.
• Use speakers with the specified impedance shown on the rear
panel of this unit.
Red: positive (+)
Black: negative (–)
Insert one bare wire into the hole in the side
of each terminal.
Red: positive (+)
Black: negative (–)
4
Tighten the knob to secure the wire.
Red: positive (+)
Black: negative (–)
9
CONNECTIONS
Connecting the power supply cord
VOLTAGE SELECTOR
To an AC wall outlet
AC power supply cord
AC OUTLETS
IMPEDANCE SELECTOR
A
OR B: 4ΩMIN
A+B: 8ΩMIN
/
/
SPEAKER
SPEAKER
SWITCHED
100W MAX.TOTAL
A
OR B: 6ΩMIN
A+B: 12ΩMIN
/
/
SPEAKER
SPEAKER
(General model)
■ Connecting the AC power supply cord
Plug the power supply cord into the AC wall outlet after
all other connections are complete.
■ AC OUTLET(S) (SWITCHED)
U.K. and Australia models ..................................... 1 outlet
Korea model .............................................................. None
Other models ........................................................ 3 outlets
Use these outlets to connect the power cords from your
other components to this unit. The power to the AC
OUTLET(S) is controlled by POWER or STANDBY/ON
on the front panel of this unit (or on the remote control).
The outlet(s) supply power to any connected component
whenever the power of this unit is turned on. For
information on the maximum power (total power
■ VOLTAGE SELECTOR
(Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE plugging
the power supply cord into the AC wall outlet.
Voltages are as follows:
Asia model.......................... AC 220/230–240 V, 50/60 Hz
General model ...... AC 110/120/220/230–240 V, 50/60 Hz
10
PLAYING AND RECORDING
PLAYING AND RECORDING
Playing a source
3
Rotate the INPUT selector on the front panel
(or press one of the input selector buttons on
the remote control) to select the input source
you want to listen to.
Note
As for AX-397 only, if the TAPE MONITOR indicator on the
front panel lights up when you listen to a source, press TAPE
MONITOR on the front panel to turn off the TAPE MONITOR
function (the TAPE MONITOR indicator turns off as a result).
The indicator of the selected input source lights up.
INPUT
POWER
STANDBY
CD/DVD PHONO
TUNER
AUX
or
2
7
MD
TAPE
STANDBY
POWER
AUX
MD
TAPE
CD/DVD
TUNER
PHONO
PURE DIRECT
CD/DVD DIRECT AMP
ON
OFF
Front panel
Remote control
VOLUME
INPUT
PHONES
SPEAKERS
BASS
TREBLE
BALANCE
LOUDNESS
REC OUT
FLAT
1
CD/DVD
1
1
1
1
1
1
TAPE
MD
AUX
TUNER
PHONO
A
B
–
30dB
2
2
4
2
4
2
4
2
2
2
4
10
STANDBY
/ON
3
3
3
3
3
3
3
9
4
4
4
8
ON
OFF
–
5
5
+
–
5
5
+
L
5
5
R
5
7
6
AUX
MD
TAPE
CD/DVD
TUNER
PHONO
8
3
4
7
1,6
Lights up
POWER
STANDBY
CD/DVD PHONO
TUNER
AUX
4
Press SPEAKERS A and/or B on the front
panel to select speakers A and/or B.
8
6
MD
TAPE
3
SPEAKERS
u
+
A
B
PRESET
d
VOLUME
–
A/B/C/D/E
ON
OFF
A/B
DISPLAY
w
e
f
DISPLAY
DIR
A
DIR
B
REC
b
s
a
DISC
Notes
CD TAPE
p
• Both SPEAKERS A and B can be selected.
• If you listen with headphones, press both switches to release
them outward to the OFF position.
1
2
Set VOLUME on the front panel
counterclockwise to the extreme end.
5
6
Play the source.
16
Rotate VOLUME on the front panel (or press
VOLUME +/– on the remote control) to adjust
the sound output level.
20
12
VOLUME
26
60
8
40
4
2
VOLUME
0
∞
+
VOLUME
–
-dB
or
Press POWER on the front panel inward to
the ON position.
POWER
Remote control
Front panel
ON
OFF
11
PLAYING AND RECORDING
7
Adjust the tonal quality by using the BASS,
TREBLE, BALANCE and LOUDNESS controls
or the CD/DVD DIRECT AMP switch on the
front panel.
BASS
TREBLE
BALANCE
LOUDNESS
FLAT
1
1
1
1
1
1
1
–
30dB
2
2
2
2
2
2
2
4
10
3
3
3
3
3
3
3
9
4
4
4
4
4
4
8
–
5
5
+
–
5
5
+
L
5
5
R
5
7
6
or
CD/DVD DIRECT AMP
Note
As for AX-497 only, you can also adjust the tonal quality by
using PURE DIRECT on the front panel.
8
Press STANDBY/ON on the front panel again
(or STANDBY on the remote control) to finish
using this unit and set it to the standby
mode.
The STANDBY indicator lights up.
STANDBY
STANDBY
/ON
or
Remote control
Front panel
STANDBY
Lights up
Note
To completely cut off power supply from the AC wall outlet,
press POWER on the front panel to release it outward to the OFF
position.
12
PLAYING AND RECORDING
■ Adjusting the LOUDNESS control
Adjusting the tonal quality
Retains a full tonal range at any volume level, thus
compensating for the human ears’ loss of sensitivity to
high and low-frequency ranges at low volume.
■ Adjusting the BALANCE control
Adjusts the sound output balance of the left and right
speakers to compensate for sound imbalance caused by
speaker locations or listening room conditions.
CAUTION
If the CD/DVD DIRECT AMP switch (or the PURE
DIRECT switch for AX-497 only) is turned on with the
LOUDNESS control set at a certain level, the input signals
bypass the LOUDNESS control, resulting in a sudden
increase in the sound output level. To prevent your ears or
the speakers from being undesirably damaged, be sure to
press the CD/DVD DIRECT AMP switch (or the PURE
DIRECT switch for AX-497 only) AFTER lowering the
sound output level or AFTER checking that the
BALANCE
1
1
2
2
3
3
4
4
L
5
5
R
■ Using the CD/DVD DIRECT AMP switch
Routes input signals from your CD or DVD player
directly to the specially built-in amplifier for the CD or
DVD player. As a result, the input signals bypass the
INPUT selector and the BASS, TREBLE, BALANCE and
LOUDNESS controls (and the TAPE MONITOR switch
for AX-397 only) and then sent to the power amplifier,
thus eliminating any alterations to the CD or DVD signals
and creating the purest possible sound.
LOUDNESS control is properly set.
1
Set the LOUDNESS control to the FLAT
position.
LOUDNESS
FLAT
1
–
30dB
2
4
10
3
9
8
Lights up
CD/DVD DIRECT AMP
5
7
6
2
Rotate VOLUME on the front panel (or press
VOLUME +/– on the remote control) to set the
sound output level to the loudest listening
level that you would listen to.
■ Using the PURE DIRECT switch
(AX-497 only)
Routes input signals from your audio sources. As a result,
the input signals bypass the BASS, TREBLE, BALANCE
and LOUDNESS controls, thus eliminating any alterations
to the audio signals and creating the purest possible sound.
VOLUME
+
VOLUME
–
or
Lights up
PURE DIRECT
Front panel
Remote control
Note
As for AX-497 only, if both the CD/DVD DIRECT AMP and the
PURE DIRECT switches are turned on, only the CD/DVD
DIRECT AMP switch will function.
3
Rotate the LOUDNESS control until the
desired volume is obtained.
LOUDNESS
■ Adjusting the BASS and TREBLE
controls
Adjusts the high and low frequency response.
FLAT
1
–
30dB
10
2
4
3
9
8
5
7
6
BASS
Increases or decreases the low frequency response.
TREBLE
Increases or decreases the high frequency response.
BASS
TREBLE
1
1
1
1
2
2
2
4
2
4
3
3
3
3
4
4
–
5
5
+
–
5
5
+
13
PLAYING AND RECORDING
Recording a source to a tape
or an MD
4
Rotate VOLUME on the front panel (or press
VOLUME +/– on the remote control) to adjust
the sound output level.
Notes
VOLUME
+
VOLUME
–
• The VOLUME, BASS, TREBLE, BALANCE and
LOUDNESS controls and the CD/DVD DIRECT AMP switch
(and the PURE DIRECT switch for AX-497 only) have no
effect on the source being recorded.
or
• Check the copyright laws in your country to record from
records, CDs, radio, etc. Recording copyright-protected
material may infringe on copyright laws.
Remote control
Front panel
■ AX-497
5
6
Begin recording on the tape deck or the MD
recorder.
STANDBY
POWER
AUX
MD
TAPE
CD/DVD
TUNER
PHONO
PURE DIRECT
CD/DVD DIRECT AMP
ON
OFF
VOLUME
INPUT
PHONES
SPEAKERS
BASS
TREBLE
BALANCE
LOUDNESS
REC OUT
Rotate the INPUT selector on the front panel
(or press TAPE or MD on the remote control)
to select TAPE or MD and then monitor the
sound being recorded on the tape deck or
the MD recorder.
FLAT
1
CD/DVD
1
1
1
1
1
1
TAPE
MD
AUX
TUNER
PHONO
A
B
–
30dB
2
2
4
2
4
2
4
2
2
2
4
10
STANDBY
/ON
3
3
3
3
3
3
3
9
4
4
4
8
ON
OFF
–
5
5
+
–
5
5
+
L
5
5
R
5
7
6
3,6
1
4
INPUT
POWER
1
Rotate the REC OUT selector on the front
panel to select the source you want to
record.
STANDBY
CD/DVD PHONO
TUNER
AUX
or
MD
TAPE
Remote control
Front panel
REC OUT
CD/DVD
TAPE
MD
AUX
TUNER
PHONO
Note
Selecting another source with the INPUT selector on the front
panel (or the corresponding input selector button on the remote
control) while recording is in progress will not affect the
recording.
2
3
Play the source.
Rotate the INPUT selector on the front panel
(or press one of the input selector buttons on
the remote control) to select the input source
you want to listen to.
INPUT
POWER
STANDBY
CD/DVD PHONO
TUNER
AUX
or
MD
TAPE
Front panel
Remote control
14
PLAYING AND RECORDING
■ AX-397
4
Begin recording on the tape deck or the MD
recorder.
y
STANDBY
POWER
AUX
MD
TAPE
CD/DVD
TUNER
PHONO
TAPE MONITOR
CD/DVD DIRECT AMP
If the 3-head tape deck is used for recording, you can monitor the
ON
OFF
sound of recording by pressing TAPE MONITOR.
VOLUME
INPUT
PHONES
SPEAKERS
BASS
TREBLE
BALANCE
LOUDNESS
FLAT
1
1
1
1
1
1
1
A
B
–
30dB
2
2
4
2
4
2
4
2
2
2
4
10
STANDBY
/ON
3
3
3
3
3
3
3
9
4
4
4
8
ON
OFF
–
5
5
+
–
5
5
+
L
5
5
R
5
7
6
2
3
1
2
Play the source.
Rotate the INPUT selector on the front panel
(or press one of the input selector buttons on
the remote control) to select the input source
you want to listen to.
INPUT
POWER
or
STANDBY
CD/DVD PHONO
TUNER
AUX
MD
TAPE
Remote control
Front panel
Note
You cannot select any input source while the TAPE MONITOR
indicator on the front panel lights up.
3
Rotate VOLUME on the front panel (or press
VOLUME +/– on the remote control) to adjust
the sound output level.
VOLUME
+
VOLUME
–
or
Remote control
Front panel
15
TROUBLESHOOTING
TROUBLESHOOTING
Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or
if the instructions below do not help, set this unit to the standby mode, disconnect the power cord, and contact the nearest
authorized YAMAHA dealer or service center.
■ General
Refer to
page
Problem
Cause
Remedy
This unit fails to turn
on.
The power supply cord is not connected or Connect the power supply cord firmly.
the plug is not completely inserted.
—
The impedance setting is incorrect.
Set the impedance to match your speakers.
The protection circuitry has been activated Check that the speaker wires are not touching each
because of a short circuit, etc. other and then turn the power of this unit back on.
The IMPEDANCE SELECTOR switch on Set the IMPEDANCE SELECTOR switch to either
—
the rear panel is not set to either end.
end when the power of this unit is turned off.
This unit has been exposed to a strong
external electric shock (such as lightning
or strong static electricity).
Set this unit to the standby mode, disconnect the
power supply cord, plug it back in after 30 seconds,
then use it normally.
No sound
Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
No appropriate input source has been
selected.
Select an appropriate input source with the INPUT
selector on the front panel (or one of the input
selector buttons on the remote control).
The TAPE MONITOR function is turned
on.
Turn off the TAPE MONITOR function.
The SPEAKERS A/B switches are not set Set the corresponding SPEAKERS A or B switch to
properly.
the ON position.
Speaker connections are not secure.
Secure the connections.
The sound suddenly
goes off.
The protection circuitry has been activated Check that the IMPEDANCE SELECTOR setting is
because of a short circuit, etc.
correct.
Check that the speaker wires are not touching each
other and then turn the power of this unit back on.
Only the speaker on
one side can be
heard.
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
Incorrect setting for the BALANCE
control.
Set the BALANCE control to the appropriate
position.
There is a lack of bass The + and – wires are connected in
Connect the speaker wires to the correct + and –
phase.
and no ambience.
reverse at the amplifier or the speakers.
A “humming” sound
can be heard.
Incorrect cable connections.
Connect the audio plugs firmly. If the problem
persists, the cables may be defective.
No connection from the turntable to the
GND terminal.
Make the GND connection between the turntable and
this unit.
The volume level is
low while playing a
record.
The record is being played on a turntable
with an MC cartridge.
The turntable should be connected to this unit through
the MC head amplifier.
—
—
The volume level
cannot be increased,
or the sound is
distorted.
The component connected to the TAPE
OUT or the MD OUT terminals of this
unit is turned off.
Turn on the power of the component.
16
TROUBLESHOOTING
The sound is
The power of this unit is turned off, or this Turn on the power of this unit.
unit is set to the standby mode.
degraded when
listening with the
headphones
connected to the CD
player or the tape
deck connected to
this unit.
The sound level is
low.
The LOUDNESS control is functioning.
Set the LOUDNESS control to the FLAT position.
The input source
cannot be changed
although the INPUT
selector is rotated.
The CD/DVD DIRECT AMP switch is
turned on.
Turn off the CD/DVD DIRECT AMP switch.
The TAPE MONITOR function is turned
on.
Turn off the TAPE MONITOR function.
Using the BASS,
TREBLE, BALANCE
and LOUDNESS
controls does not
affect the tonal
quality.
The CD/DVD DIRECT AMP switch (or
the PURE DIRECT switch for AX-497
only) is turned on.
The CD/DVD DIRECT AMP switch (or the PURE
DIRECT switch for AX-497 only) must be turned off
to use those controls.
■ Remote control
Refer to
page
Problem
Cause
Remedy
The remote control
does not work nor
function properly.
Wrong distance or angle.
The remote control will function within a maximum
range of 6 m (19.7 ft) and no more than 30 degrees
off-axis from the front panel.
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries.
17
SPECIFICATIONS
SPECIFICATIONS
POWER SECTION
• Minimum RMS Output Power
CONTROL SECTION
• Input Sensitivity/Input Impedance
(8 Ω , 20 Hz to 20 kHz, 0.019% THD)
PHONO .................................................................. 2.5 mV/47 kΩ
CD, etc. .................................................................. 150 mV/47 kΩ
[AX-497] .............................................................. 85 W + 85 W
[AX-397] .............................................................. 60 W + 60 W
(6 Ω , 20 Hz to 20 kHz, 0.038% THD)
[AX-497] .......................................................... 100 W + 100 W
[AX-397] .............................................................. 70 W + 70 W
• Output Level/Output Impedance
REC OUT
[AX-497] ............................................... 195 mV/1.6 kΩ or less
[AX-397] ............................................... 165 mV/1.6 kΩ or less
• Dynamic Power (IHF) (8/6/4/2 Ω)
• Headphone Output/Impedance
[AX-497] ....................................................... 130/150/185/220 W
[AX-397] ....................................................... 100/120/140/150 W
CD, etc. (Input 1 kHz, 150 mV, 8 Ω , 0.019% THD)
[AX-497] ................................................................ 0.3 V/680 Ω
[AX-397] .............................................................. 0.25 V/680 Ω
• Maximum Output Power
(1 kHz, 0.7% THD, 4 Ω) [U.K. and Europe models only]
[AX-497] ......................................................................... 120 W
[AX-397] ........................................................................... 95 W
(1 kHz, 10% THD, 8/6 Ω)
• Channel Separation
CD, etc. (5.1 kΩ input shorted, 1/10 kHz) ....... 65/50 dB or more
• Tone Control Characteristics
BASS
[AX-497]
Boost/Cut (20 Hz) ........................................................... ±10 dB
Turnover Frequency ........................................................ 350 Hz
TREBLE
[Asia, General, China and Korea models only] .... 130/150 W
[AX-397]
[Asia, General and China models only] ................ 100/110 W
Boost/Cut (20 kHz) ......................................................... ±10 dB
Turnover Frequency ....................................................... 3.5 kHz
• IEC Output Power [U.K. and Europe models only]
(1 kHz, 0.019% THD, 8 Ω)
• Continuous Loudness Control
[AX-497] ......................................................................... 100 W
Attenuation (1 kHz) ........................................................... –30 dB
[AX-397] ........................................................................... 75 W
• Power Band Width
GENERAL
• Power Supply
[AX-497] (0.04% THD, 42.5 W, 8 Ω) .................10 Hz to 50 kHz
[AX-397] (0.04% THD, 30 W, 8 Ω) ....................10 Hz to 50 kHz
[U.S.A. and Canada models] ............................. AC 120 V, 60 Hz
[Asia model] .................................. AC 220/230–240 V, 50/60 Hz
[General model] ............... AC 110/120/220/230–240 V, 50/60 Hz
[China model] .................................................... AC 220 V, 50 Hz
[Korea model] (AX-497 only)............................ AC 220 V, 60 Hz
[Australia model] ............................................... AC 240 V, 50 Hz
[U.K. and Europe models] ................................. AC 230 V, 50 Hz
• Damping Factor
20 Hz to 20 kHz, 8 Ω ..................................................240 or more
• Maximum Input Signal
PHONO (1 kHz, 0.003% THD) .......................... 115 mV or more
CD, etc. (1 kHz, 0.5% THD) ................................... 2.2 V or more
• Frequency Response
• Power Consumption
CD, etc. (20 Hz to 20 kHz) .......................................... 0 ± 0.5 dB
CD/DVD DIRECT AMP ON (10 Hz to 100 kHz) ...... 0 ± 1.0 dB
[AX-497]
[U.S.A. and Canada models] ............................. 220 W, 300 VA
[Asia model] .................................................................... 190 W
[Other models] ................................................................. 220 W
[AX-397] ............................................................................ 170 W
• RIAA Equalization Deviation
PHONO ........................................................................... ± 0.3 dB
• Total Harmonic Distortion
PHONO to REC OUT
(20 Hz to 20 kHz, 3 V) .......................................... 0.003% or less
CD, etc. to SP OUT
• Standby Power Consumption
[Asia and General models]
(110/120 V).........................................................................1.1 W
(220/230-240 V) .................................................................2.7 W
[Other models] ..................................................................... 1.1 W
(The power consumption is 0 W when the POWER switch is
released outward to the OFF position.)
(20 Hz to 20 kHz, 42.5 W, 8 Ω) ............................. 0.009% or less
• Signal to Noise Ratio (IHF-A Network)
PHONO (input shorted) ..........................................88 dB or more
CD (input shorted)
CD/DVD DIRECT AMP ON ............................ 110 dB or more
• Maximum Power Consumption [General models only]
(1 kHz, 6 Ω , 10% THD)
• Residual Noise (IHF-A Network)
[AX-497] ......................................................................... 490 W
[AX-397] ......................................................................... 400 W
[AX-497]
CD/DVD DIRECT AMP ON .......................................... 35 µV
PURE DIRECT ON ......................................................... 90 µV
[AX-397]
CD/DVD DIRECT AMP ON .......................................... 35 µV
CD/DVD DIRECT AMP OFF ....................................... 100 µV
• AC Outlets
[U.K. and Australia models] ............... 1 (Total 100 W maximum)
[Korea model] ....................................................................... None
[General model]......................................3 (Total 50 W maximum)
[Other models] .................................... 3 (Total 100 W maximum)
• Dimensions (W x H x D) ................................. 435 x 151 x 390 mm
(17-1/8” x 5-15/16” x 15-11/32”)
• Weight
[AX-497] ...................................................... 9.1 kg (20 lbs. 1 oz.)
[AX-397] ...................................................... 8.3 kg (18 lbs. 5 oz.)
* Specifications are subject to change without notice.
18
|