Whirlpool Dishwasher ADG 7470 User Manual

Quick reference guide  
Chart  
ON  
BUTTON  
PROGRAMME SELECTION BUTTON  
BEFORE USING THE APPLIANCE FOR THE  
FIRST TIME CAREFULLY READ THIS QUICK  
REFERENCE GUIDE AND THE ASSEMBLY  
INSTRUCTIONS! THE GUARANTEE IS NOT  
APPLICABLE IF FAULTS ARE CAUSED BY  
INCORRECT USE OF THE APPLIANCE.  
Press button “P” (repeatedly) until the indicator of the required programme lights up (see “Table of  
programmes” below).  
OFF  
BUTTON  
START BUTTON  
The indicator lights up during operation, flashes when a fault occurs and goes off at the end of the programme.  
START BUTTON RESET FUNCTION  
Press this button for at least 2 seconds; the selected programme and options are cancelled. Main failure  
displays (repeated flashing of the START indicator lamp) can be cancelled by RESETTING. Detailed  
instructions are given in chapter “What to do if...”.  
Consumption  
Table of programmes  
Programmes Loading instructions  
Deter-  
gent  
Litres kWh  
P
Minutes 1)  
Crockery to be washed later.  
cold  
5.0  
0.02  
10  
30  
Pre-Wash  
1
Lightly soiled crockery, with no  
dried-on food. * Use of tablets  
not recommended.  
X * 13.0 0.70  
Quickwash 40°C  
2
3
4
Normally soiled crockery.  
Energy-saving programme.  
2)  
50°C  
Eco  
X
X
15.0 1.05  
17.0 1.65  
165  
145  
Recommended programme for  
heavily soiled crockery, especially  
suitable for pots and pans.  
Intensive  
70°C  
1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions  
(without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible  
with sensor programmes as a result of the appliances automatic calibration system.  
2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for  
detailed information on the EN/Standard loading comparison test and other tests, contact the following address:  
ADG 7470  
5019 396 01787  
GB -1-  
 
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)  
Daily check  
1
Visual indicator (depending  
on model). Screw on the cap.  
Salt residues around cap  
need to be removed.  
Add salt  
Visual indicator  
(depending  
on model).  
Fill the salt  
(never add  
detergent!).  
min. 1.5 kg  
max. 2 kg  
reservoir with  
water before the  
first wash only.  
Unscrew cap.  
Salt indicator  
(depending on  
the model)  
The salt level indicator lamp may remain lit for the duration of several wash cycles. If the  
water hardness level falls within category (soft), no salt is required.  
The indicator lamp on the control panel lights  
up when SALT NEEDS TO BE ADDED.  
orange: OK.  
clear: NEEDS TO BE ADDED  
Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator  
The rinse aid dosage can be adjusted to the  
detergent used. The lower the setting,  
the less rinse aid is dispensed  
Visual  
indicator  
2
(factory setting: position 4).  
Press the button to open the cover B. Using a  
coin or similar object, turn the arrow to the  
desired setting. After adjusting the rinse aid  
setting, shut the cover again.  
If required,  
open the cover  
B (press right  
button).  
Add rinse aid  
to the max.  
line ~ 150 ml  
The indicator lamp on the control panel lights up when RINSE AID NEEDS TO BE  
ADDED.  
Rinse aid indicator (depending on model)  
dark: OK.  
clear: NEEDS TO BE ADDED  
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.  
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid  
setting will not improve the situation.  
Detergents with rinse aid incorporated may be effective only with longer programmes. In the case of shorter programmes, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend  
to form excess suds.  
Adding detergent - Use only detergent specifically for dishwashers in accordance with the suppliers recommendations  
Daily use  
Tablet / gel / powder  
Use only one tablet per one  
cycle, only placed in detergent  
dispenser.  
3
By pressing  
dedicated ribs  
shut the cover.  
Open the cover A Only fill the  
(press left button). detergent dispenser  
prior to starting a  
All types of tablets can be  
used, but for 2 in 1 type  
adding of salt is mandatory.  
wash programme.  
GB -3-  
 
How to load UPPER RACK  
How to load the racks  
(In some models only)  
A - Multipurpose support: Different positions for long  
utensils, cups and glasses.  
B - Adjustable flaps: In horizontal position for cups/long utensils,  
in raised position for plates and stemware.  
(In some models only)  
C - Cutlery basket: It can be placed in the upper rack when the  
“Half load/Multizone” option is selected.  
4
D - Adjustable glass holder  
How to adjust upper rack height (if available)  
- It could be useful to lift up upper rack to have more space in  
lower rack or bring it down to load long stem glasses.  
- Grasp and take out the two lateral handles (E) (must be on same  
level) and lift up or take down the upper rack.  
How to remove upper rack (if available)  
- It could be useful to remove upper rack to load bulky items in  
lower rack.  
- Open the two retainers (F) to take off the upper rack. When  
the upper rack is in place the retainers must always be closed.  
F - OPEN  
F - CLOSED  
How to load LOWER RACK  
(depending on the model)  
G - Foldable plate holders: They can be folded down to load pots  
or  
H- Fixed plate holders  
I - Cutlery basket (or J model)  
K - Grid: Helps to keep the cutlery separate for better washing results.  
H
I
J
Arrange crockery so that water does not collect in cavities, ensuring that the spray arms turn freely. Only use dishwasher-proof crockery and dishes. Do not use the dishwasher for washing wooden  
items, aluminium, tin, silver cutlery or decorated crockery (unglazed). In the baskets, dishes (e.g. plates, bowls, pots) must be placed in a correct way to let water flow down!  
5
Switching on the appliance  
GB -4-  
 
Select programme  
Quick, permanent or alternating  
Overview of programmes  
The max. possible number of programmes is illustrated in the chapter “Chart”. The corresponding programmes for your appliance can be found on the panel (page 1).  
6
Choose programme according to the attached table of programmes (page 1).  
Duration of the programme depends on the external conditions in the apartment, temperature and pressure etc.  
Wash cycle  
The dishwasher door must be closed and the water tap open.  
Change the programme in progress:  
To load crockery, open the door with caution:  
Press the START button (for 2 seconds) until the START indicator lamp  
switches off.  
Close the door.  
(Water drains for up to 60 seconds).  
Open the door.  
7
Beware of hot steam!  
Close the door again.  
The programme resumes the cycle from where it was interrupted.  
Select a new programme.  
Press the START button.  
The wash cycle can be interrupted at any time by pressing START (see chapter “What to do if...”).  
Switch off the appliance Everything o.k. ...  
Exercise caution when opening the door: beware of hot steam.  
Only press the OFF button once the START indicator lamp has switched off.  
8
All the indicator lamps switch off. Unload the appliance, starting from the lower rack in order to avoid any residual drips of water falling onto crockery below.  
Maintenance and care  
Maintenance and care  
Screw on filter cylinder NOTE MARK!  
9
Filters  
Check and  
clean if  
Unscrew filter  
cylinder, remove it  
and fine sieve...  
Rinse under running  
water ...  
Insert  
necessary  
Rectifying minor faults yourself ...  
Insert and screw on lower and upper arms tightly.  
10  
Spray arms  
Remove  
Unscrew  
and remove  
lower arm ...  
Unscrew  
and remove  
upper arm ...  
Clean spray  
nozzles under  
running water  
(use toothpicks if  
necessary) ...  
blockages/  
deposits.  
GB -5-  
 
What to do if...  
If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action,  
quickly restoring normal appliance operation.  
The appliance...  
Possible causes...  
Solutions...  
...is not working/will not start  
-
-
The appliance must be switched on.  
-
-
-
Check the household circuit fuse if there is no power supply.  
The dishwasher door doesn't close.  
“Delayed start” option is ON.  
Check if the dishwashers door is closed.  
Check whether the “Delayed start” option (if available) has been selected. If it has, the appliance will only  
start once the set time has elapsed. If necessary, set the delayed start to “0” (RESET the appliance).  
-
-
...shows “F1” on the display or the START  
indicator lamp flashes once  
The water supply temperature is below 3°C.  
-
Check that the water supply temperature is above 3°C.  
...shows “F4” on the display or the START  
indicator lamp flashes 4 times  
-
-
-
-
Dirty filters.  
-
-
-
-
-
Clean the filters.  
Kinked drain hose.  
Syphon hose connection closed.  
Water tap closed.  
The drain hose must not be kinked.  
The closure disk of the syphon hose connection must be removed.  
The water tap must be open.  
...shows “F6” on the display or the START  
indicator lamp flashes 6 times  
The water inlet hose must not be kinked and the relative inlet filter in the water tap connector must not be  
clogged.  
-
-
-
Kinked water inlet hose or clogged inlet filters.  
Water pressure too low.  
...shows “F7” on the display or the START  
indicator lamp flashes 7 times  
-
-
The water tap must be fully open during water inlet (minimum capacity: 0.5 litres per minute).  
The water inlet hose must not be kinked and the relative inlet filter in the water tap connector must not be  
dirty.  
Kinked water inlet hose or clogged inlet filters.  
...shows “F8” on the display or the START  
indicator lamp flashes 8 times  
-
-
Dirty or clogged filters.  
-
-
-
The filters must not be dirty or clogged.  
Too little water in the dishwashers water system.  
Concave items (e.g. bowls, cups) must be arranged facing downwards in the rack.  
The drain hose must be fitted correctly (for high mounted appliances, leave min. 200-400 mm from the  
lower edge of the appliance) - see Assembly instructions.  
Reset the appliance (see below).  
-
-
Drain hose incorrectly fitted.  
Many different causes.  
...shows other “F” faults on the display or  
the START indicator lamp flashes Xx times  
-
After taking the above course of action, the fault message must be reset. In the majority of cases the fault is thus eliminated.  
RESET: Press the START button for approx. 2 seconds until the indicator lamp switches off or press the RESET button (depending on model)  
Close the door.  
Water drains automatically for up to 60 seconds.  
The appliance is now ready to be restarted.  
Crockery and cutlery...  
...are not perfectly clean/have food residues  
Possible causes...  
Too little space between dishes (incorrect arrangement  
of the concave items in the rack).  
Too little detergent; detergent too old or incorrectly  
stored.  
Solutions...  
-
-
-
-
Arrange crockery so that items do not touch each other. Concave items (e.g. bowls, cups) must be  
arranged facing downwards in the rack.  
If necessary, use more detergent, observing the manufacturers indications as regards dosage. Always store  
detergent in a dry place and do not store it for excessively long periods of time.  
-
-
Temperature not high enough for heavily soiled crockery.  
-
-
For heavily soiled crockery, select a wash programme with a higher temperature (see table of programmes on page 1).  
Loading of the dishwasher using lower and upper rack  
at the same time with “Half load/Multizone” option.  
If you select the “Half load/Multizone” option (if available), remember to load only the upper rack or only  
the lower rack to increase washing power and thus obtain optimum wash results.  
In the event of frequent use of the Eco 50°C programme (if available), from time to time select the  
Intensive 70°C programme (if available).  
The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see page 5,  
“Maintenance and care”).  
-
-
-
Frequent use of Eco 50°C.  
-
-
Clogged spray arms; filters dirty or not fitted correctly.  
Spray arms impeded by crockery or cutlery.  
-
The spray arms must be able to turn freely and must not be impeded by crockery or cutlery.  
GB -6-  
 
What to do if...  
Crockery and cutlery...  
...salt indicator lit  
...have deposits: regeneration salt residue  
Possible causes...  
Use tablets for soft water.  
Solutions...  
-
-
-
-
Set “Detergent type” option; if this option is not available, it is normal for the salt indicator to light up.  
In areas with very hard water, more regeneration salt needs to be added (see page 2 “How to set water  
hardness”).  
Water too hard.  
-
-
-
-
Salt reservoir cap open.  
Not enough rinse aid.  
-
-
-
-
Close the salt reservoir cap properly.  
If you use a combined action detergent, try adding more rinse aid.  
Synthetic materials do not dry well; if wet at end of cycle, wipe dry.  
...are not dry  
Plastic containers dry badly.  
Clean dishes left in dishwasher for a long time after end  
of cycle (e.g. when using “delayed start” option).  
In this situation, the presence of drops of water on dishes and on the sides of the dishwasher is normal. Try  
releasing the door 5 minutes before removing the dishes.  
-
-
Incorrect arrangement of the concave items in the rack. - Arrange crockery so that water does not collect in cavities.  
Incorrect dosage the rinse aid.  
-
-
Increase the dosage of rinse aid - see page 3, Adding rinse aid”.  
The rapid programme is intended for quickly washing lightly soiled dishes. If used for a full load of medium/  
heavy soiled dishes, the dishes may not dry completely. If so, select a standard-length programme. For best  
results, open the door after the end of the programme and wait 15 minutes before unloading the dishwasher.  
-
Rapid programme selected.  
...have discoloured plastic parts  
-
Tomato sauce, for example, can lead to discolouring of plastic parts. Powder detergent is recommended as  
it allows slightly higher doses to be used for improved whitening. Programmes with higher wash  
temperatures should be used.  
-
-
Tomato/Carrot juice.  
...opaque glasses, etc  
Dishes unsuitable for washing in dishwashers  
(porcelain),  
-
-
Only use dishwasher-proof crockery and dishes.  
...removable deposits on glasses  
...glasses not sparkling  
Dishes should be put together, to avoid touching each other. Do not put glassware together in baskets.  
Use suitable programme for glass.  
-
-
Usage of incorrect programmes for glasses.  
Not conform of glasses to washing in dishwashers  
(porcelain).  
-
Some kinds of glass cannot be washed in the dishwasher.  
...permanent deposits on glasses  
-
Rainbow effect.  
-
-
-
-
This phenomenon is irreversible. We recommend in future:  
Change the control of system of dosage of softener.  
Be careful – follow recommended detergent dosage.  
For combined action tablets see detergent producers recommendations.  
...tea cups darken and dirt does not  
disappear after washing in dishwasher  
-
-
-
Not known.  
-
-
This phenomenon is inevitable. Theine alters colours permanently.  
...rust marks  
...other marks  
...streaks  
Salty or acidic food residues can cause rust marks even on stainless steel cutlery. To avoid this, always use  
the pre-wash programme if the dishes are to be washed later.  
Pre-wash programme not used.  
Rinse aid dosage too low.  
-
-
-
In the presence of marks, increase the rinse aid dosage (see page 3, Adding rinse aid”). If you use a  
combined action detergent, try adding more rinse aid.  
In the presence of streaks, reduce the rinse aid dosage (see page 3, Adding rinse aid”). If you use a  
combined action detergent which includes rinse aid, do not add any additional rinse aid.  
-
-
Rinse aid dosage too high.  
...suds  
Unsuitable dosage of detergent/rinse aid.  
Only use the amount of detergent/rinse aid required, since excessive amounts can lead to excess suds.  
GB -7-  
 
Disconnect the mains plug  
What to do if...  
If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap.  
Contact the After-sales Service (see warranty).  
Before contacting our After-Sales Service, take note of the following:  
- the description of the fault,  
- the appliance type and model,  
- the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side:  
Precautions and general recommendations  
1. Packing  
-
-
Before cleaning or carrying out maintenance, disconnect the mains plug and turn off the water tap; also in  
the event of any malfunction.  
Repairs and technical modifications must be carried out exclusively by a qualified technician.  
The packaging materials are 100% recyclable and marked with the recycling symbol  
.
2. Removing the packaging and inspecting the contents  
After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt,  
contact a qualified technician or your local retailer.  
7. Resistance to frost  
If the appliance is placed in surroundings exposed to the risk of frost, it must be drained completely. Turn off  
the water tap, remove the inlet and outlet hoses, and let all the water drain away. Make sure there is at least  
1 kg of dissolved regeneration salt in the salt reservoir, to protect the appliance from temperatures of up to  
-20°C. When the programme resumes, an error message may be displayed. “F1”/START indicator flashes  
once: pour half a litre of warm water into the bottom of the dishwasher. “F6”/START indicator flashes 6  
times: the appliance must remain at an ambient temperature of min. 5°C for at least 24 hours. After  
eliminating these faults, RESET the appliance (see chapter “What to do if...”).  
3. Before using the dishwasher for the first time  
-
-
The appliance is designed to operate at ambient temperatures of between 5°C and 45°C.  
This dishwasher has been tested by the manufacturer to ensure it functions correctly. Such testing may  
leave slight drips/water marks which will disappear with the first wash.  
4. Energy and water savings  
-
-
-
Do not rinse crockery under running water.  
8. Disposal  
Always fully load the dishwasher before running it or select the “Half load/Multizone” option (if available).  
If ecological energy sources are available such as solar panel heating, heat pumps or centralised heating  
systems, the appliance may be connected to the hot water mains up to a maximum temperature of 60°C.  
Make sure the water inlet hose is of the correct type (“70°C Max” or “90°C Max”).  
-
The appliance is manufactured using recyclable materials. If you decide to scrap the dishwasher, it must be  
disposed of in compliance with local waste disposal regulations. Make it unusable by cutting off the power  
cord. To prevent situations of potential danger to children (e.g. danger of suffocation), break the lock of the  
door so that it can no longer be closed.  
5. Child safety  
-
This appliance is marked according to the European directive 2002/96/CE on Waste Electrical and  
Electronic Equipment (WEEE). By ensuring that this appliance is scrapped suitably, you can help prevent  
potentially damaging consequences for the environment and health. Unsuitable disposal of an appliance of  
-
-
-
Keep the packaging materials out of the reach of children.  
Children must not be allowed to play with the dishwasher.  
Store the detergent, rinse aid and salt out of the reach of children.  
this type as household waste could have detrimental effects on the environment. The symbol  
on the  
6. Safety warnings  
appliance, or on documentation enclosed with the appliance, indicates that this product must not be  
treated as household waste, but must be delivered to the nearest collection centre for the recycling of  
electrical and electronic appliances. Disposal must be carried out in accordance with local environmental  
regulations for waste disposal. For further information on the treatment, recovery and recycling of this  
appliance, contact your competent local authority, the collection service for household waste or the shop  
where you purchased the appliance.  
-
The appliance is not intended for use by children or physically or mentally impaired persons, unless  
adequately supervised by a responsible adult capable of guaranteeing safe use of the appliance.  
Do not operate the appliance in the open air.  
Do not store flammable materials in close proximity to the dishwasher.  
The water in the dishwasher is not potable.  
Do not use solvents inside the dishwasher: risk of explosion!  
Be careful when the door is open: risk of tripping!  
The open dishwasher door can only support the weight of the loaded rack when pulled out. Do not rest  
objects on the open door or sit or stand on it.  
-
-
-
-
-
-
EC Declaration of conformity  
This appliance has been designed, constructed and distributed in compliance with the safety requirements of  
EC Directives:  
2006/95/CE, 89/336/CE, 93/68/CE and 2002/95/CE (RoHS Directive).  
Loading Capacity: 12 place settings.  
-
Sharp items that might cause injury (e.g. knives), must be placed in the cutlery basket with the sharp end  
facing downwards. Long-handled utensils must be arranged horizontally in the upper rack, with the sharp  
end facing away from the front of the appliance.  
We reserve the right to make technical modifications.  
GB -8-  
 

Westinghouse Power Hammer AK 1 50 9 User Manual
Whirlpool Oven GBD307PRB00 User Manual
Whirlpool Ventilation Hood GZ5730XRB0 User Manual
Whirlpool Ventilation Hood GZ7930XGS0 User Manual
Whirlpool Washer Dryer LA57l5XP User Manual
Whirlwind Music Mixer MIX 5 User Manual
White Outdoor Lawn Mower Z 185L, Z 205, Z 225 User Manual
Windsor Vacuum Cleaner SC326 10052220 User Manual
Zanussi Freezer 42FF User Manual
Z Microsystems Network Card 8X User Manual