Whirlpool Clothes Dryer wgd9200s User Manual

®
Gas Dryer  
PRODUCT MODEL NUMBERS  
WGD9200S  
WGD9300V  
WGD9400S  
WGD9400V  
WGD9500T  
WGD9600T  
REQUIREMENTS  
Electrical: A 4-wire, single-phase, 120/240-volt, 60-Hz,  
AC-only electrical supply on a separate 30-amp circuit,  
fused on both sides of the line is required. A time-delay  
fuse or circuit breaker is recommended. Connect to an  
individual branch circuit.  
Exhaust venting: Exhaust your dryer to the outside.  
4" (10.16 cm) diameter vent is required. Rigid or flexible  
heavy metal exhaust vent must be used. The total length  
of flexible metal vent should not exceed 7-3/4 ft. (2.4 m).  
Do not use plastic or metal foil vent. Exhaust outlet hood  
must be at least 12" (30.5 cm) from the ground or any  
object that may be in the path of the exhaust.  
An individual manual shutoff valve must be installed  
within six (6) feet (1.8m) of the dryer in accordance with  
the National Fuel Gas Code, ANSI Z223.1. The location  
should be easy to reach for opening and closing.  
*®TEFLON is a registered trademark of E.I. Dupont De  
Nemours and Company  
1/2" IPS pipe is recommended.  
3/8" approved aluminum or copper tubing is acceptable  
for lengths under 20 ft (6.1 m) if local codes and gas  
supplier permit.  
If you are using Natural gas, do not use copper tubing.  
Lengths over 20 ft (6.1 m) should use larger tubing and a  
different size adapter fitting.  
If your dryer has been converted to use LP gas, 3/8" LP  
compatible copper tubing can be used. If the total length  
of the supply line is more than 20 ft (6.1 m), use larger  
pipe.  
Dryer gas pipe: The gas pipe that comes out through  
the rear of your dryer has a 3/8" male thread.  
B
*6¼"  
(15.9 cm)  
Gas supply: This dryer is equipped for use with Natural  
gas. It is design-certified by CSA International for LP  
(propane or butane) gases with appropriate conversion.  
No attempt shall be made to convert the appliance from  
the gas specified on the model/serial rating plate for use  
with a different gas without consulting your gas company.  
Must include 1/8" NPT minimum plugged tapping  
accessible for test gauge connection, immediately  
upstream of the gas connection to the dryer.  
NOTE: Pipe joint compounds that resist the action of LP  
gas must be used. Do not use TEFLON® tape.*  
Use an elbow and a 3/8" flare x 3/8" NPT adapter fitting  
between the flexible gas connector and the dryer gas  
pipe, as needed to avoid kinking.  
This dryer must be connected to the gas supply line with  
a listed flexible gas connector that complies with the  
standard for connectors for gas appliances, ANSI Z21.24  
or CSA 6.10.  
1½"  
A
(3.8 cm)  
A. ½" NPT gas supply line  
B. 3/8NPT dryer pipe  
NOTE: If the dryer is mounted on a pedestal, the gas pipe  
height must be an additional 10" (25.4 cm) or 15.5"  
(39.4 cm) from the floor, depending on the pedestal  
model. For a garage installation, the gas pipe height must  
be an additional 18" (46 cm) from the floor.  
PRODUCT DIMENSIONS  
D
Steam  
(Electric or Gas)  
Non-Steam  
(Electric or Gas)  
A
B
C
D
38" (9652 mm)  
32 9/16" (686 mm)  
27" (686 mm)  
38" (9652 mm)  
31 1/2" (800 mm)  
27" (686 mm)  
A
52 9/16" (1335 mm)  
51 1/2" (1308 mm)  
B
* Most installations require a minimum 5" (127 mm) clearance behind the dryer for  
the exhaust vent with elbow.  
C
Page 1 of 3  
Because Whirlpool Corporation policy includes a continuous commitment to improve  
our products, we reserve the right to change materials and specifications without notice.  
Dimensions are for planning purposes only. For complete details, see Installation  
Instructions packed with product. Specifications subject to change without notice.  
Ref. W10224610  
11-09-08  
 
®
Gas Dryer  
PRODUCT MODEL NUMBERS  
WGD9200S  
WGD9300V  
WGD9400S  
WGD9400V  
WGD9500T  
WGD9600T  
RECOMMENDED INSTALLATION SPACING FOR RECESSED OR CLOSET INSTALLATION, WITH STACKED WASHER AND DRYER  
Dimensions shown are for recommended spacing.  
48 in.2  
*
6"* (152 mm)  
(310 cm2)  
3"* (76 mm)  
Steam  
(Electric or Gas)  
Non-Steam  
(Electric or Gas)  
A*  
5 ½" (140 mm)  
5" (127 mm)  
76"  
(1930 mm)  
*Required spacing  
NOTE: Some models are not recommended for stacked  
recessed or closet installation.  
3"* (76 mm)  
24 in.2  
*
1"  
(25 mm)  
27"  
(686 mm)  
1"* (25 mm)  
1"  
(25 mm)  
A*  
(155 cm2)  
* Required spacing  
CUSTOM UNDERCOUNTER INSTALLATION – DRYER ONLY  
Dimensions shown are for minimum spacing.  
Steam  
(Electric or Gas)  
Non-Steam  
(Electric or Gas)  
A
A
0" (0 mm)  
0" (0 mm)  
B
B
38" (9652 mm)  
1" (25 mm)  
38" (9652 mm)  
1" (25 mm)  
C*  
D
C*  
D
E*  
27" (686 mm)  
1" (25 mm)  
27" (686 mm)  
1" (25 mm)  
* Required spacing  
E*  
*Required spacing  
NOTE: Some models are not recommended for undercounter  
installation.  
EXHAUST VENTING  
NOTE: Side and bottom exhaust installations have a 90º turn inside  
the dryer. To determine maximum exhaust length, add one 90º turn  
to the chart.  
A and B: Recommended hood styles.  
C: Acceptable hood style.  
B
Number  
Type of vent  
Box /louvered  
hoods  
Angled  
hoods  
C
90º elbows  
4"  
(102 mm)  
A
0
1
2
3
4
Rigid metal  
Rigid metal  
Rigid metal  
Rigid metal  
Rigid metal  
64 ft (20 m)  
54 ft (16.5 m)  
44 ft (13.4 m)  
35 ft (10.7 m)  
27 ft (8.2 m)  
58 ft (17.7 m)  
48 ft (14.6 m)  
38 ft (11.6 m)  
29 ft (8.8 m)  
21 ft (6.4 m)  
4"  
(102 mm)  
2½"  
(64 mm)  
4"  
(102 mm)  
A. Louvered hood style  
B. Box hood style  
C. Angled hood style  
Select the route that will provide the straightest and most direct path outdoors.  
Plan the installation to use the fewest number of elbows and turns. Use the fewest  
90° turns possible.  
Do not use vent runs longer than specified in vent length chart.  
Determine the number of elbows you will need.  
Page 3 of 3  
Because Whirlpool Corporation policy includes a continuous commitment to improve  
our products, we reserve the right to change materials and specifications without notice.  
Dimensions are for planning purposes only. For complete details, see Installation  
Instructions packed with product. Specifications subject to change without notice.  
Ref. W10224610  
11-09-08  
 

Weed Eater Trimmer 545186763 User Manual
Weil McLain Boiler CGi Series 2 User Manual
West Bend Back to Basics Blender SR1000 User Manual
Whirlpool Freezer EH120F User Manual
Whirlpool Freezer EH151FXRQ00 User Manual
Whirlpool Microwave Oven AMW 470 User Manual
White Rodgers Thermostat 1TKF9 User Manual
Yamaha Outboard Motor 6D6 28199 10 User Manual
Yamaha Stereo System GX707 User Manual
Zanussi Washer FL 828 User Manual