R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
TWIST--N--EDGEt
TE500CXL
For Occasional Use Only
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
530086934
4/24/02
Copyright E2002 Electrolux Home Products, Inc.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or ab-
normal swellings. Prolonged use in cold
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek med-
ical attention. An anti--vibration system does
not guarantee the avoidance of these prob-
lems. Users who operate power tools on a
continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many internal combustion engines be
equipped with a spark arresting screen. If you
operate in a locale where such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violation of the law. For normal
homeowner use, the muffler and spark arrest-
ing screen will not require any service. After
50 hours of use, we recommend that your
muffler be serviced or replaced by an autho-
rized service dealer.
CUTTING SAFETY
WARNING: Inspect the area before
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects
can damage the trimmer head and be thrown
causing serious injury.
S Use only for trimming, scalping, mowing, edg-
ing and sweeping. Do not use for pruning or
hedge trimming.
S Keep firm footing and balance. Do not over-
reach.
S Keep all parts of your body away from muffler
and spinning line. Keep engine below waist
level. A hot muffler can cause serious burns.
S Cut from your left to your right. Cutting on
right side of the shield will throw debris away
from the operator.
S Use only in daylight or good artificial light.
S Use only for jobs explained in this manual.
TRANSPORTING AND STORAGE
S Allow engine to cool before storing or trans-
porting in vehicle.
S Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the carbu-
retor by starting the engine and letting it run
until it stops.
S Store unit and fuel in area where fuel vapors
cannot reach sparks or open flames from
water heaters, electric motors or switches,
furnaces, etc.
S Store unit so line limiter blade cannot acci-
dentally cause injury. The unit can be hung
by the tube.
S Store unit out of reach of children.
ASSEMBLY
NOTE: Knob must be assembled on the
right hand side of the unit as shown in the il-
lustration.
WARNING: If received assembled,
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
Examine parts for damage. Do not use dam-
aged parts.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to rattle in the
empty fuel tank.
2. Make sure the bolt is seated in the hex--
shaped hole in the handle.
3. Pivot the handle to a comfortable position.
4. Tighten knob securely.
ATTACHING SHIELD
Finding fuel or oil residue on muffler is normal
due to carburetor adjustments and testing
done by the manufacturer.
ATTACHING THE ASSIST HANDLE
NOTE: Be sure to attach the assist handle to
the unit before attaching the shield.
1. Assemble handle to the unit as shown;
make sure bottom of handle is seated in
the groove in the trigger housing.
WARNING: The shield must be prop-
erly installed. The shield provides partial protec-
tion to the operator and others from the risk of
thrown objects, and is equipped with a line limit-
er blade which cuts excess line to the proper
length. The line limiter blade (on underside of
shield) is sharp and can cut you.
For proper orientation of shield, see KNOW
YOUR TRIMMER illustration in OPERATION
section.
Groove
3
1. Remove wing nut from shield.
2. Insert bracket into slot as shown.
3. Pivot shield until bolt passes through hole
in bracket.
Bracket
Slot
Wing Nut
4. Securely tighten wing nut onto bolt.
Gearbox
Shield
OPERATION
KNOW YOUR TRIMMER
READ THIS INSTRUCTION MANIT.
Compare the illustrations with yontrols
and adjustments. Save this man
Throttle Trigg
ON/OFF Switch
Muffler
Starter
Handle
Fuel Mix
Fill Cap
ON/STOP SWITCH
CHOKE
The ON/STOP switch is used to stop the
engine. To stop the engine, push and release
the engine ON/STOP switch.
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving the choke lever to the FULL CHOKE
position. After the engine attempts to start, move
the choke lever to the HALF CHOKE position.
Once engine has started, move the choke lever
to the OFF CHOKE position.
PRIMER BULB
The PRIMER BULB removes air from the car-
buretor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original form.
oil at a ratio of 40:1. A 40:1 ratio is obtained by
mixing 3.2 ounces of oil with 1 gallon of
unleaded gasoline. DO NOT USE automotive
oil or boat oil. These oils will cause engine
damage. When mixing fuel, follow instructions
printed on container. Once oil is added to
gasoline, shake container momentarily to
assure that the fuel is thoroughly mixed. Always
read and follow the safety rules relating to fuel
before fueling your unit.
BEFORE STARTING ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you be-
gin. If you do not understand the safety rules,
do not attempt to fuel your unit. Call
1-800-554--6723.
FUELING ENGINE
WARNING: Remove fuel cap slowly
when refueling.
IMPORTANT
This engine is certified to operate on unleaded Experience indicates that alcohol blended
gasoline. Before operation, gasoline must be fuels (called gasohol or using ethanol or
mixed with a good quality synthetic 2-cycle methanol) can attract moisture which leads to
air-cooled engine oil designed to be mixed at a separation and formation of acids during stor-
ratio of 40:1. Poulan/Weed Eater brand age. Acidic gas can damage the fuel system
synthetic oil is recommended. Mix gasoline and of an engine while in storage.
4
To avoid engine problems, empty the fuel sys- 7. Pull starter rope sharply until engine runs,
tem before storage for 30 days or longer.
Drain the gas tank, start the engine and let it
run until the fuel lines and carburetor are
empty. Use fresh fuel next season.
Never use engine or carburetor cleaner prod-
ucts in the fuel tank or permanent damage
may occur. See the STORAGE section for
additional information.
but no more than 6 pulls.
NOTE: If the engine doesn’t start after 6
pulls (at the HALF CHOKE position),
move the choke lever to the FULL
CHOKE position and press the primer
bulb 6 times. Squeeze and hold the
throttle trigger and pull the starter rope 2
more times. Move the choke lever to the
HALF CHOKE position and pull the start-
er rope until the engine runs, but no more
than 6 pulls. If the engine still doesn’t
start, it is probably flooded. Proceed to
STARTING A FLOODED ENGINE.
HOW TO STOP YOUR UNIT
S To stop the engine, push and release the
engine ON/STOP switch. The switch will
automatically return to the ON position.
Wait 5 seconds before attempting to restart
unit to allow switch to reset.
8. Once the engine starts, allow it to run 10 se-
conds, then move the choke lever to the
OFF CHOKE position. Allow the unit to run
for 30 more seconds at OFF CHOKE be-
fore releasing the throttle trigger.
S If engine does not stop, move choke lever
to FULL CHOKE position.
Engine
Choke Lever
ON/STOP
Switch
NOTE: If engine dies with the choke le-
ver in the OFF CHOKE position, move
the choke lever to the HALF CHOKE
position and pull the rope until engine
runs, but no more than 6 pulls.
HALF
FULL
OFF
STARTING A WARM ENGINE
1. Move the choke lever to the HALF
CHOKE position.
2. Squeeze and hold the throttle trigger.
Keep throttle trigger fully squeezed until
the engine runs smoothly.
3. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
4. Allow engine to run 15 seconds, then
move the choke lever to the OFF CHOKE
position.
NOTE: If engine has not started, pull start-
er rope 5 more pulls. If engine still does not
run, it is probably flooded.
HOW TO START YOUR UNIT
WARNING: The trimmer head will
turn while starting the engine. Avoid any con-
tact with the muffler. A hot muffler can cause
serious burns.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
the choke lever in the OFF CHOKE position;
then, pull the rope to clear the engine of ex-
cess fuel. This could require pulling the starter
handle many times depending on how badly
the unit is flooded.
If the unit still doesn’t start, refer to
TROUBLESHOOTING TABLE or call
1-800-554--6723.
Starting Position
1. Set unit on a flat surface.
2. Slowly press the primer bulb 6 times.
3. Move choke lever to the FULL CHOKE
position.
4. Squeeze the throttle trigger fully and hold
through all remaining steps.
OPERATING POSITION
Starter Handle
Choke
Lever
ALWAYS WEAR:
Eye
Protection
Long Pants
Heavy Shoes
Muffler
Cut from your left to your right.
Primer Bulb
5. Pull starter rope handle sharply until engine
sounds as if it is trying to start, but do not
pull rope more than 6 times.
WARNING: Always wear eye protec-
tion. Never lean over the trimmer head. Rocks
6. As soon as engine sounds as if it is trying to or debris can ricochet or be thrown into eyes
start, move choke lever to HALF CHOKE
position.
and face and cause blindness or other serious
injury.
5
Do not run the engine at a higher speed than
necessary. The cutting line will cut efficiently
flower beds, but it also can cut the tender
bark of trees or shrubs and scar fences.
when the engine is run at less than full throttle. S For trimming or scalping, use less than full
At lower speeds, there is less engine noise and
vibration. The cutting line will last longer and will
be less likely to “weld” onto the spool.
throttle to increase line life and decrease
head wear, especially:
S During light duty cutting.
S Near objects around which the line can wrap
such as small posts, trees or fence wire.
S For mowing or sweeping, use full throttle for
a good clean job.
TRIMMING -- Hold the bottom of the trimmer
head about 3 in. (8 cm) above the ground and
at an angle. Allow only the tip of the line to
make contact. Do not force trimmer line into
work area.
Always release the throttle trigger and allow the
engine to return to idle speed when not cutting.
To stop engine:
S Release the throttle trigger.
S Push and release the engine ON/STOP
switch.
TWIST AND EDGE
The Twist and Edge feature allows for easy
edging of sidewalks, patios, driveways, etc.
1. Pull the tab toward the engine.
2. Twist the tube to the edging position; re-
lease tab.
Trimming
TRIMMER LINE ADVANCE
SCALPING -- The scalping technique re-
moves unwanted vegetation. Hold the bottom
The cutting head advances line automati-
cally. Do not tap head on the ground to ad- of the trimmer head about 3 in. (8 cm) above
vance line. This may break parts and cause
cutting head to malfunction.
Upon unit start up, the line will advance auto-
matically to the correct cutting path length.
Always keep the shield in place when the tool
is being operated.
the ground and at an angle. Allow the tip of the
line to strike the ground around trees, posts,
monuments, etc. This technique increases
line wear.
Scalping
WARNING: Use only 0.080” (2 mm)
diameter round line. Other sizes and shapes
of line will not advance properly and will result in
improper cutting head function or can cause se-
rious injury. Do not use other materials such as
wire, string, rope, etc. Wire can break off during
cutting and become a dangerous missile that
can cause serious injury.
CUTTING METHODS
WARNING: Use minimum speed
and do not crowd the line when cutting around
hard objects (rock, gravel, fence posts, etc.),
which can damage the trimmer head, become
MOWING -- Your trimmer is ideal for mowing
in places conventional lawn mowers cannot
reach. In the mowing position, keep the line
parallel to the ground. Avoid pressing the
entangled in the line, or be thrown causing a head into the ground as this can scalp the
serious hazard.
ground and damage the tool.
S The tip of the line does the cutting. You will
achieve the best performance and
minimum line wear by not crowding the line
into the cutting area. The right and wrong
ways are shown below.
Mowing
SWEEPING -- The fanning action of the rotating
line can be used for a quick and easy clean up.
Keep the line parallel to and above the surfaces
being swept and move the tool from side to side.
S The line will easily remove grass and
weeds from around walls, fences, trees and
6
Sweeping
Edging
EDGING-- Adjust trimmer to the edging posi-
tion (see TWIST AND EDGE section). Allow
only the tip of the line to make contact. Do not
force trimmer line into work area.
MAINTENANCE
CLEAN AIR FILTER
WARNING: Disconnect the spark
plug before performing maintenance except
for carburetor adjustments.
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
S Air Filter
S Housing Screws
S Assist Handle Screw
S Debris Shield
1. Clean the cover and the area around it to
keep dirt from falling into the carburetor
chamber when the cover is removed.
2. Remove parts by pressing button to re-
lease air filter cover.
NOTE: To avoid creating a fire hazard or
producing harmful evaporative emissions, do
not clean filter in gasoline or other flammable
solvent.
3. Wash the filter in soap and water.
4. Allow filter to dry.
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S ON/STOP Switch -- Ensure ON/STOP
switch functions properly by pushing and
releasing the switch. Make sure engine
stops. Wait 5 seconds before attempting to
restart unit to allow switch to reset. Restart
engine and continue.
5. Add a few drops of oil to the filter;
squeeze the filter to distribute oil.
6. Replace parts.
er
Screws
S Fuel Tank -- Discontinue use of unit if fuel
tank shows signs of damage or leaks.
S Debris Shield -- Discontinue use of unit if
debris shield is damaged.
Air Filter Cover
INSPECT AND CLEAN UNIT AND
DECALS
REPLACE SPARK PLUG
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
decals using a damp cloth with a mild deter-
gent.
Replace the spark plug each year to ensure
the engine starts easier and runs better. Set
spark plug gap at 0.025 in. Ignition timing is
fixed and nonadjustable.
S Wipe off unit with a clean dry cloth.
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and
discard.
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
socket wrench.
4. Reinstall the spark plug boot.
7
SERVICE AND ADJUSTMENTS
2. Insert one end of line into center cavity of
LINE REPLACEMENT
empty spool. Ensure line will feed into
spool in the direction shown on the spool
(clockwise).
Pre--wound spools offer the most convenient
method for replacing line and ensuring opti-
mum performance.
3. Continue feeding line into spool, leaving 4
-- 6 inches (10 -- 15 cm) unwound from
center of spool.
S Replacement spools are color--coded to
ensure use of the correct spool with your
unit. Be sure to use the same color spool as
the existing spool.
INSTALLING SPOOL WITH LINE
NOTE: Always clear dirt and debris from cut-
ting head components when performing any
type of maintenance.
1. Install replacement spool.
2. Thread line through line guide ring.
Line through guide ring
S Hold spool and unscrew cap by turning in
the direction shown on top of the cap.
S Remove line guide ring and spool.
Slot
Line guide ring
Cap
Replacement Spool
3. Rest guide ring on spool and place line in
slot. Allow line to extend 4 -- 6 inches (10
-- 15 cm) from center of spool.
4. Ensure line remains in slot while screw-
ing cap on to the shaft. Only tighten cap
hand tight!
Spool
Use a pre--wound spool or refill spool with
line. If using a pre--wound spool, remove tape
strip from line and spool.
REFILLING THE SPOOL WITH LINE
WARNING: Use only 0.080” (2 mm)
diameter round line. Other sizes and
shapes of line will not advance properly and
will result in improper cutting head function or
can cause serious injury. Do not use other
materials such as wire, string, rope, etc. Wire
can break off during cutting and become a
dangerous missile that can cause serious in-
jury.
CARBURETOR ADJUSTMENT
Your carburetor is equipped with limiter caps.
Carburetor adjustment is a complicated task.
We recommend that you take your unit to an au-
thorized service dealer. Damage will occur if
you turn the needles beyond the limiter stops.
1. Cut a length of 30 feet of 0.080” (2 mm)
diameter round Weed Eater" brand line.
Feed line in
direction
shown on
spool.
Spool
STORAGE
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
S Store unit and fuel well out of the reach of
children.
WARNING: Perform the following
steps after each use:
S Allow engine to cool before storing or trans-
porting.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
8
SEASONAL STORAGE
ENGINE
Prepare unit for storage at end of season or if S Remove spark plug and pour 1 teaspoon of
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
S Clean the entire unit before lengthy
storage.
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recom-
mended type and heat range.
S Store in a clean dry area.
S Lightly oil external metal surfaces.
S Clean air filter.
S Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
S At the beginning of the next season, use
only fresh fuel having the proper gasoline to
oil ratio.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual, see message la-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to the gasoline
in the fuel tank or fuel storage container. Fol-
low the mix instructions found on stabilizer
container. Run engine at least 5 minutes after
adding stabilizer.
OTHER
S Do not store gasoline from one season to
another.
S Replace your gasoline can if it starts to rust.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing all of the
recommended remedies below except remedies that require operation of the unit.
TROUBLE
CAUSE
REMEDY
Engine will not
start.
1. Engine flooded.
1. See “Starting a Flooded Engine” in
Operation Section.
2. Fill tank with correct fuel mixture.
3. Install new spark plug.
4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
2. Fuel tank empty.
3. Spark plug not firing.
4. Fuel not reaching
carburetor.
5. Carburetor requires
adjustment.
5. See “Carburetor Adjustment” in
Service and Adjustments Section.
Engine will
not idle
properly.
1. Carburetor requires
adjustment.
2. Crankshaft seals worn.
3. Compression low.
1. See “Carburetor Adjustment” in
Service and Adjustments Section.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer.
1. Air filter dirty.
1. Clean or replace air filter.
2. Clean or replace plug
and regap.
3. See “Carburetor Adjustment” in
Service and Adjustments Section.
4. Contact an authorized service dealer.
Engine will not
accelerate,
lacks power,
or dies under
a load.
2. Spark plug fouled.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
5. Compression low.
5. Contact an authorized service dealer.
Engine
1. Choke partially on.
2. Fuel mixture incorrect.
1. Adjust choke.
2. Empty fuel tank and refill with
correct fuel mixture.
smokes
excessively.
3. Air filter dirty.
4. Carburetor requires
adjustment.
3. Clean or replace air filter.
4. See “Carburetor Adjustment” in
Service and Adjustments Section.
1. See “Fueling Engine” in Operation
section.
Engine runs
hot.
1. Fuel mixture incorrect.
2. Replace with correct spark plug.
3. See “Carburetor Adjustment” in
Service and Adjustments Section.
4. Contact an authorized service dealer.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
9
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS, INC.,
er predelivery setup or normal adjustments
warrants to the original purchaser that each explained in the instruction manual.
new Weed Eater" brand gasoline tool or at- THIS WARRANTY GIVES YOU SPECIFIC
tachment is free from defects in material and LEGAL RIGHTS, AND YOU MAY HAVE
workmanship and agrees to repair or replace
under this warranty any defective gasoline
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
product or attachment as follows from the NO CLAIMS FOR CONSEQUENTIAL OR
original date of purchase.
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
2 YEARS-- Parts and Labor, when used for
household purposes.
90 DAYS -- Parts and Labor, when used for
commercial, professional, or income produc- SOME STATES DO NOT ALLOW LIMITA-
ing purposes.
30 DAYS -- Parts and Labor, if used for rental RANTY LASTS OR THE EXCLUSION OR
purposes. LIMITATIONS OF INCIDENTAL OR CON-
TIONS ON HOW LONG AN IMPLIED WAR-
This warranty is not transferable and does not SEQUENTIAL DAMAGES, SO THE ABOVE
cover damage or liability caused by improper LIMITATIONS OR EXCLUSION MAY NOT
handling, improper maintenance, or the use APPLY TO YOU.
of accessories and/or attachments not spe- The policy of ELECTROLUX HOME PROD-
cifically recommended by ELECTROLUX
HOME PRODUCTS, INC., for this tool. Addi-
UCTS, INC., is to continuously improve its
products. Therefore, ELECTROLUX HOME
tionally, this warranty does not cover tune- PRODUCTS, INC., reserves the right to
ups, spark plugs, filters, cutting line, or rotat- change, modify, or discontinue models, de-
ing head parts that will wear and require
signs, specifications, and accessories of all
replacement with reasonable use during the products at any time without notice or obliga-
warranty period. This warranty does not cov- tion to any purchaser.
U.S. EPA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGA-
maintenance. As the small off--road engine
TIONS: The U. S. Environmental Protection owner, you should be aware that POULAN/
Agency and POULAN/WEED EATER, DIVI-
SION OF WCI OUTDOOR PRODUCTS, INC.,
WEED EATER may deny you warranty cover-
age if your small off--road engine or a part of it
are pleased to explain the emissions control has failed due to abuse, neglect, improper main-
system warranty on your year 2001--2004 small tenance, unapproved modifications, or the use
off--road engine. POULAN/WEED EATER of parts not made or approved by the original
must warrant the emission control system on equipment manufacturer. You are responsible
your small off--road engine for the periods of for presenting your small off--road engine to a
time listed below provided there has been no POULAN/WEED EATER authorized repair
abuse, neglect, or improper maintenance of center as soon as a problem exists. Warranty
your small off--road engine. Your emission con- repairs should be completed in a reasonable
trol system includes parts such as the carbure-
amount of time, not to exceed 30 days. If you
tor and the ignition system. Where a warrant- have any questions regarding your warranty
able condition exists, POULAN/WEED EATER rights and responsibilities, you should contact
will repair your small off--road engine at no cost your nearest authorized service center or call
to you. Expenses covered under warranty in-
clude diagnosis, parts and labor. MANUFAC- WARRANTY COMMENCEMENT DATE: The
TURER’S WARRANTY COVERAGE: If any warranty period begins on the date the small
POULAN/WEED EATER at 1--800--554--6723.
emissions related part on your engine (as listed off--road engine is purchased. LENGTH OF
under Emissions Control Warranty Parts List) is COVERAGE: This warranty shall be for a peri-
defective or a defect in the materials or work- od of two years from the initial date of purchase.
manship of the engine causes the failure of such WHAT IS COVERED: REPAIR OR RE-
an emission related part, the part will be repaired PLACEMENT OF PARTS. Repair or replace-
or replaced by POULAN/WEED EATER.
OWNER’S WARRANTY RESPONSIBILI-
ment of any warranted part will be performed at
no charge to the owner at an approved POU-
TIES: As the small off--road engine owner, you LAN/WEED EATER servicing center. If you
are responsible for the performance of the re- have any questions regarding your warranty
quired maintenance listed in your instruction rights and responsibilities, you should contact
manual. POULAN/WEED EATER recom-
your nearest authorized service center or call
mends that you retain all receipts covering POULAN/WEED EATER at 1--800--554--6723.
maintenance on your small off--road engine, but WARRANTY PERIOD: Any warranted part
POULAN/WEED EATER cannot deny warran-
which is not scheduled for replacement as re-
ty solely for the lack of receipts or for your failure quired maintenance, or which is scheduled only
to ensure the performance of all scheduled for regular inspection to the effect of ”repair or
10
replace as necessary” shall be warranted for 2
years. Any warranted part which is scheduled
CLAIM: If you have any questions regarding
your warranty rights and responsibilities, you
for replacement as required maintenance shall should contact your nearest authorized service
be warranted for the period of time up to the first center or call POULAN/WEED EATER at
scheduled replacement point for that part. 1--800--554--6723. WHERE TO GET WAR-
DIAGNOSIS: The owner shall not be charged
RANTY SERVICE: Warranty services or re-
for diagnostic labor which leads to the deter- pairs shall be provided at all POULAN/WEED
mination that a warranted part is defective if the EATER service centers. Call 1--800--554--6723.
diagnostic work is performed at an approved MAINTENANCE, REPLACEMENT AND RE-
POULAN/WEED EATER servicing center.
CONSEQUENTIAL DAMAGES: POULAN/
PAIR OF EMISSION RELATED PARTS: Any
POULAN/WEED EATER approved replace-
WEED EATER may be liable for damages to ment part used in the performance of any war-
other engine components caused by the failure ranty maintenance or repair on emission related
of a warranted part still under warranty. WHAT parts will be provided without charge to the own-
IS NOT COVERED: All failures caused by
abuse, neglect, or improper maintenance are CONTROL WARRANTY PARTS LIST: Car-
not covered. ADD--ON OR MODIFIED buretor, Ignition System: Spark Plug (covered
er if the part is under warranty. EMISSION
PARTS: The use of add--on or modified parts up to maintenance schedule), Ignition Module.
can be grounds for disallowing a warranty claim. MAINTENANCE STATEMENT: The owner is
POULAN/WEED EATER is not liable to cover responsible for the performance of all required
failures of warranted parts caused by the use of maintenance as defined in the instruction
add--on or modified parts. HOW TO FILE A manual.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
11
|